Table of Contents
Advertisement
Quick Links
INSTALLATION and OPERATION MANUAL
Break Away Fitting For Submersible Pumps
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Manual Index
BARNES
BARNES
Models: Without Check Valve
Models: With Check Valve
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
®
BAFEZ-1.25 x 2
BAFEZ-2 x 2
BAFEZ-2 x 3
BAFEZ-3 x 3
BAFEZCV-1.25 x 2
BAFEZCV-2 x 2
Form No. 101701-Rev. F
Advertisement
Table of Contents
Related Manuals for Barnes BAFEZ-1.25x2
Summary of Contents for Barnes BAFEZ-1.25x2
- Page 1 Manual Index BARNES BARNES ® INSTALLATION and OPERATION MANUAL Break Away Fitting For Submersible Pumps Models: Without Check Valve BAFEZ-1.25 x 2 BAFEZ-2 x 2 BAFEZ-2 x 3 BAFEZ-3 x 3 Models: With Check Valve BAFEZCV-1.25 x 2 BAFEZCV-2 x 2 IMPORTANT! Read all instructions in this manual before operating pump.
-
Page 2: Table Of Contents
RETURNED GOODS POLICY .................14 WARRANTY REGISTRATION Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc. 1997, 1998, 2002, 2/06, 9/06 Alteration Rights Reserved... -
Page 3: Safety First
SAFETY FIRST! Please Read This Before Installing Or Operating Pump. This information is provided for SAFETY and to PREVENT CAUTION ! Do not block or restrict discharge hose, as EQUIPMENT PROBLEMS. To help recognize this information, discharge hose may whip under pressure. observe the following symbols: IMPORTANT! Warns about hazards that can result WARNING ! Do not wear loose clothing that may... -
Page 4: Specification
SECTION: A - SPECIFICATIONS: Each BAFEZ break away fi tting consists of a cast iron The BAFEZ’s can basically be used on any pump with the base elbow which is bolted to the fl oor of the wet well, appropiate discharge size that does not exceed 200 lbs lower guide rail supports, cast iron movable elbow (91kg) in weight, which do not generate in excess of 150 (BAFEZCV’s include ball check valve and clean-out... -
Page 5: Dimensions (Figures 1 & 2)
1.25” & 2” with Check Valve Recommend 3’ to 5’ per sec. max. FIGURE 1 MODEL PART PUMP x BAF Disch. x Disch. BAFEZCV-1.25x2 114035 1.25" X 2" 3.27 3.31 4.69 7.40 12.07 4.33 (83) (84) (119) (188) (307) (110) BAFEZCV-2x2 114036 2"... - Page 6 1.25”, 2” and 3” without Check Valve FIGURE 2 MODEL PART PUMP x BAF Disch. x Disch. BAFEZ-1.25x2* 114030 1.25" x 2" 2.87 (73) 3.31 (84) 4.75 (121) 7.52 (191) 12.07 (307) 4.33 (110) BAFEZ-2x2 114031 2" x 2" 3.20 (81) 3.31 (84)
-
Page 7: General Information
Compound #242 then be sprayed with a rust-inhibiting oil. (General Purpose) Thread Locking B-4) Service Centers: Compound For the location of the nearest Barnes Service Center, check RC609 HM128 #RC609 your Barnes representative or Crane Pumps & Systems, Inc., (High Strength) Service Department in Piqua, Ohio, telephone (937) 778-8947 or in Brampton, Ontario, Canada (905) 457-6223. -
Page 8: Replacement Parts
SECTION E: REPLACEMENT PARTS E-1) Ordering Replacement Parts: When ordering replacement parts, always furnish the following information: 1. Product Model 2. Part Description 3. Part Number 4. Quantity Required 5. Shipping Instructions 6. Billing Instructions Product improvements are made from time to time. The latest part design will be furnished as it is interchangeable with the old part. -
Page 9: Bafezcv's Parts List / Instructions (Figure 4)
Models with Check Valve BAFEZCV-1.25x2, BAFEZCV-2x2 FIGURE 4 Pump to Moveable Instruction 1.) Remove Elbow/Check Valve #1 from Sealing Plate #2 2.) Thread Elbow/Check Valve #1 into pump discharge. 3.) Bolt on Sealing Plate #2. 4.) Set lifting chain bail with one end on guide plate #3 and on pump lifting eye (or lifting bail) and balance for center of gravity. -
Page 10: Bafez-1.25X2 Parts List / Instructions (Figure 5)
Models Without Check Valve BAFEZ-1.25x2 FIGURE 5 Pump to Moveable Instruction 1.) Remove set screw from elbow #1 2.) Thread adaptor #4 into discharge of pump with sealing plate #2 and guide plate #3 attached. 3.) Tighten set screw to secure elbow with sealing plate and guide plate square. -
Page 11: Bafez-1.50X2, 2X2, 2X3, 3X3 Parts List / Instructions (Fig. 6)
Models Without Check Valve BAFEZ-2x2, BAFEZ-2x3, BAFEZ-3x3 FIGURE 6 Pump to Moveable Instruction 1.) Remove Elbow #1 from Sealing Plate #2 2.) Thread Elbow #1 into pump discharge. 3.) Bolt on Sealing Plate #2. 4.) Set lifting chain bail with one end on guide plate #3 and on pump lifting eye (or lifting bail) and balance for center of gravity. -
Page 12: Intermediate Supports (Figures 7 & 8)
2" Stainless P/N: 100568 Used with: BAFEZ's P/N's: 114030 & 114031 BAFEZCV's P/N's: 114035 & 114036 FIGURE 7 3" Stainless P/N: 100569 Used with: BAFEZ's P/N's: 114032 & 114033 FIGURE 8 The intermediate guide rail support is required for every 13 feet (4m) of guide rail. Mount the intermediate between each section of guide rail pipe, by inserting each pipe over the nipples of the intermedi- ate. - Page 13 Limited 24 Month Warranty Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state.
-
Page 14: Returned Goods Policy
IMPORTANT! WARRANTY REGISTRATION Your product is covered by the enclosed Warranty. To complete the Warranty Registration Form go to: http://www.cranepumps.com/ProductRegistration/ If you have a claim under the provision of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.