Table of Contents
Advertisement
Quick Links
INSTALLATION and OPERATION MANUAL
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc. constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
BARNES
BARNES
Submersible Sewage Ejector
®
Series:
3SE-L
(Vertical Discharge)
1.5 & 2HP
3450RPM, 60Hz
3SEH-L
(Horizontal Discharge)
1.5 & 2HP
3450RPM, 60Hz
(Single Seal)
83 West Drive, Brampton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 132771-Rev. F
Advertisement
Table of Contents
Related Manuals for Barnes 3SEH-L
Summary of Contents for Barnes 3SEH-L
- Page 1 INSTALLATION and OPERATION MANUAL Submersible Sewage Ejector Series: 3SE-L (Vertical Discharge) 1.5 & 2HP 3450RPM, 60Hz 3SEH-L (Horizontal Discharge) 1.5 & 2HP 3450RPM, 60Hz (Single Seal) IMPORTANT! Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc. constant product improvement program, product changes may occur.
-
Page 2: Table Of Contents
SEAL TOOL KIT ( see parts list) PRESSURE GAUGE KIT (see parts list) Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc 1994, 2002, 3/06, 9/06 Alteration Rights Reserved... -
Page 3: Safety First
SAFETY FIRST! Please Read This Before Installing Or Operating Pump. This information is provided for SAFETY and to PREVENT Do not block or restrict discharge hose, as discharge hose EQUIPMENT PROBLEMS. To help recognize this information, may whip under pressure. observe the following symbols: IMPORTANT! Warns about hazards that can result in WARNING! - DO NOT wear loose clothing that may... -
Page 4: Pump Specifications
SECTION: A - PUMP SPECIFICATIONS: DISCHARGE ....3” NPT, Vertical SPEED ......3450RPM, 60Hz (nominal) 3” Flanged, Horizontal UPPER BEARING: LIQUID TEMPERATURE .. 104°F (40°C) Continuous 1.5 & 2HP ..Single Row, Ball, Oil Lubricated MOTOR HOUSING ..Cast Iron ASTM, Class 30 Load ..... -
Page 5: General Information
B-4) Service Centers: Install the intermediate support brackets, if required. Make sure For the location of the nearest Barnes Service Center, check the rails are in a true vertical position so the pump will clear your Barnes representative or Crane Pumps & Systems, Inc.,... -
Page 6: Start-Up Operation
As the motor is oil filled, no lubrication or other maintenance is required, and generally Barnes Pumps will give very TEMPERATURE SENSOR ELECTRICAL RATINGS reliable service and can be expected to operate for years on... -
Page 8: Service And Repair
1) Inspect motor chamber for oil level and contamination and pressure and remove the gauge assembly. If the pressure repair as required per section F-1. does not hold, then the leak must be located and repaired. 2) Inspect impeller and body for excessive build-up or clogging and repair as required per section F-2. - Page 9 To test the temperature sensor (P1 / P2, optional), check for continuity between the wire leads (see Figure 10). If found to be defective, contact a motor service station or Barnes Pumps Service department. Inspect motor winding for shorts and check resistance values. Check rotor for wear. If rotor or the stator windings are defective, the complete motor must be replaced.
- Page 10 POWER CORD (30) CONTROL CORD (32) CAP SCREW (16) CAP SCREW (16) LOCKWASHER (11) LOCKWASHER (11) COMPRESSION FLANGE (30a) COMPRESSION FLANGE (32a) SNAP RING (41) SNAP RING (41) O-RING (40) O-RING (40) TERMINAL BLOCK (23) TERMINAL BLOCK (38) TERMINAL TERMINAL FIGURE 5 F-3.3) Wiring Connections: F-3.4) Cable Assemblies:...
- Page 11 Motor & Bearing Bracket Stationary Member (31a) Rotating Member (31b) Polished Face Out Stationary Seal Plate (1) Seal Pusher Seal Pusher Bullet FIGURE 8 FIGURE 7 Important ! - DO NOT Hammer On The Seal It is extremely important to keep seal faces clean during Pusher- It Will Damage The Seal Face.
-
Page 12: Replacement Parts
G-2 PART NUMBER: SECTION: G REPLACEMENT PARTS The part number consists of a six (6) digit number, which appears in the catalog. A one or two letter suffix may follow this number to designate the design configuration. This number is G-1 ORDERING REPLACEMENT PARTS: used for ordering and obtaining information. - Page 13 FIGURE 10...
-
Page 14: Trouble Shooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... -
Page 15: Cross-Section (Figure 11A & 11B)
CROSS SECTION (VERTICAL DISCHARGE) OPTIONAL TEMPERATURE SENSOR CABLE ASSEMBLY FIGURE 11a... - Page 16 CROSS SECTION (HORIZONTAL DISCHARGE) OPTIONAL TEMPERATURE SENSOR CABLE ASSEMBLY FIGURE 11b...
-
Page 17: Exploded View (Figure 12)
EXPLODED VIEW WITH OPTIONAL TEMP. SENSOR CABLE ASSY. FIGURE 12... -
Page 18: Parts List
PARTS KITS SEAL REPAIR KIT: 1.5 & 2.0HP....P/N 130181 (+) 8, 10, 31, 40 SERVICE: 1.5 & 2.0HP ......P/N 130208 (◊) 2, 3, 6, 8, 10, 14, 15, 18, 25, 31, 34, 35, 40, 41, SEAL TOOL KIT: 1.5 & 2.0HP ....P/N 085443 PRESSURE GAUGE KIT ......P/N 085343 PARTS LIST - Standard ITEM... - Page 19 TABLE 2 - POWER & SENSOR CORD SETS TERMINAL BLOCK MODEL NO 30 FT. POWER 50 FT. POWER 100 FT. POWER POWER 3SE1522L 109498XC 109498XF 109498XL 103760 3SE1592L 109492XC 109492XF 109492XL 103586 3SE1542L 103742XC 103742XF 103742XL 103583 3SE1552L 103742XC 103742XF 103742XL 103583 3SE2022L...
- Page 20 Notes...
-
Page 21: Warranty
IMPORTANT! WARRANTY REGISTRATION Your product is covered by a warranty: www.cranepumps.com/downloadables/CATALOGS_OIPMs/Warranty/24MonthWarranty.pdf If you have a claim under the provisions of the warranty, contact your local Crane Pumps & Systems, Inc. Distributor.