Mitsubishi Electric FR-F700PJ Series Manual page 16

Filterpack
FR-BFP2-0.4K, 0.75K, 1.5K, 2.2K, 3.7K
FR-BFP2-H0.4K, H0.75K, H1.5K, H2.2K, H3.7K
2-φ4.5 hole
Rating
plate
1.6 4.5
D1
D2 D2
D
(GND) (R) (S)
Capacity W W1 W2
0.4K, 0.75K 68
1.5K, 2.2K 108 55 26.5 188 178 80 55 12.5 200 220
3.7K 170 120 25
H0.4K, H0.75K  108 55 26.5 188 178 55 30 12.5 200 220
H1.5K to H3.7K 108 55 26.5 188 178 80 55 12.5 200 220
 The 400V class H0.4K and H0.75K have no slit.
Parameter unit (option) (FR-PU07)
Enclosure surface operation panel (option) (FR-PA07)
16
2-φ4.5 hole
4.5 1.6
W2 W1 W2
W
L1
L
Crimping terminal φ4.3
(T) (P1) (P)
H H1 D D1 D2
30 19 218 208 60 30 15
188 178 65 40 12.5 220 240
<Outline drawing>
(14.2)
83
∗1
∗1

When installing the FR-PU07 on the enclosure, etc., remove screws or fix the
screws to the FR-PU07 with M3 nuts.

Select the installation screw whose length will not exceed the effective depth of the
80.3
installation screw hole.
<Outline drawing>
68
FR-BFP2-5.5K, 7.5K, 11K, 15K
FR-BFP2-H5.5K, H7.5K, H11K, H15K
2-φC hole
Rating
plate
2.3 C1
D1 12.5
12.5
D
L-bracket for rear
panel installation of
the inverter

(enclosed)
 For rear panel installation, an L-bracket is required. The L-bracket
is enclosed, but not installed to the inverter at the factory.
(Unit mm)
L L1 Capacity
240 220
5.5K, 7.5K
11K
15K
H5.5K, H7.5K
H11K
H15K
<Enclosure cut dimension drawing>
25.05
(11.45)
40 40
∗1
Air-bleeding
hole
∗1
26.5
26.5
<Enclosure cut dimension drawing>
22
22
59
2-φC hole
25 145
(25)
195
220
L2
L
310
Crimping terminal φC2
(R) (S) (T) (P1) (P) (GND)
H H1 H2 D D1 C C1 C2
210 198 6 75 50 4.5 4.5 5.3 270 400
320 305 7.5 85 60 6 6
320 305 7.5 85 60 6 6
210 198 6 75 50 4.5 4.5 4.3 270 400
320 305 7.5 85 60 6 6
320 305 7.5 85 60 6 6
4-R1
4-φ4 hole
Effective depth of the
(
installation screw hole 5.0)
∗2
M3 screw
(Unit: mm)
2-M3 screw
(Unit: mm)
C1 2.3
25
(Unit mm)
L L2
5.3 280 280
6.4 260 260
4.3 280 280
6.4 260 260