Danfoss VLT AutomationDrive FC 301 Operating Instructions Manual page 61

Specifications
Type designation
1)
High/Normal overload
Typical shaft output at 550 V (kW)
Typical shaft output at 690 V [kW]
Enclosure protection rating IP20
Enclosure protection rating IP21, IP55
Output current
Continuous (525-550V) [A]
Intermittent (60 s overload) (525-550V) [A]
Continuous (551-690V) [A]
Intermittent (60 s overload) (551-690V) [A]
continuous KVA (at 550 V) [KVA]
continuous KVA (at 690 V) [KVA]
Maximum input current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 690 V) [A]
Intermittent (60 s overload) (at 690 V) [A]
Additional specifications
Maximum cable-cross section for mains
2
and motor [mm ] ([AWG])
Maximum cable cross-section for load
share and brake [mm 2 ] ([AWG])
2)
Maximum cable cross-section for mains
2
disconnect [mm ] ([AWG])
Estimated power loss
at rated maximum load [W] 3)
4)
Efficiency
Table 8.12 B4, C2, C3 Enclosure, Mains Supply 525-690 V IP20/IP21/IP55 - Chassis/NEMA1/NEMA 12 (FC 302 only), P30K-P75K
For fuse ratings, see chapter 8.7 Fuses and Circuit Breakers.
1) High overload=150% or 160% torque for a duration of 60 s. Normal overload=110% torque for a duration of 60 s.
2) The 3 values for the maximum cable cross-section are for single core, flexible wire and flexible wire with sleeve, respectively.
3) Applies for dimensioning of frequency converter cooling. If the switching frequency is higher than the default setting, the power losses may
increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer to
www.danfoss.com/vltenergyefficiency
4) Efficiency measured at nominal current. For energy efficiency class see chapter 8.4 Ambient Conditions. For part load losses see
www.danfoss.com/vltenergyefficiency.
MG33AP02
Operating Instructions
P30K P37K
HO NO HO NO
22 30 30 37
30 37 37 45
B4 C3
C2 C2
36.0 43.0 43.0 54.0
54.0 47.3 64.5 59.4
34.0 41.0 41.0 52.0
51.0 45.1 61.5 57.2
34.3 41.0 41.0 51.4
40.6 49.0 49.0 62.1
36.0 49.0 49.0 59.0
54.0 53.9 72.0 64.9
36.0 48.0 48.0 58.0
54.0 52.8 72.0 63.8
95, 70, 70
(3/0, 2/0, 2/0)
600 740 740 900
0.98 0.98
Danfoss A/S © Rev. 07/2014 All rights reserved.
P45K P55K
HO NO HO NO
37 45 45 55
45 55 55 75
C3 D3h
C2 C2
54.0 65.0 65.0 87.0
81.0 71.5 97.5 95.7
52.0 62.0 62.0 83.0
78.0 68.2 93.0 91.3
51.4 61.9 61.9 82.9
62.1 74.1 74.1 99.2
59.0 71.0 71.0 87.0
87.0 78.1 105.0 95.7
58.0 70.0 70.0 86.0
87.0 77.0 105 94.6
150 (300 MCM)
95 (3/0)
185, 150, 120
(350 MCM, 300
MCM, 4/0)
900 1100 1100 1500
0.98 0.98
P75K
HO NO
50 75
75 90
D3h
C2
87.0 105
130.5 115.5
83.0 100
124.5 110
82.9 100
99.2 119.5
87.0 99.0
129 108.9
- -
- -
8 8
-
1500 1800
0.98
59