Table of Contents
Advertisement
TROUBLESHOOTING
20 20
20 20
20
Problem
Dirty debris bag. Nozzle height set too high or too low. Hose kit cap
Will not vacuum or has poor
missing. Clogged nozzle or exhaust. Excessive quantity of debris.
vacuum performance.
Loose or out of balance impeller or loose engine.
Abnormal vibration.
Throttle in off position. Out of gasoline. Bad or old gasoline.
Engine will not start.
Spark Plug wire disconnected. Dirty air cleaner.
Transmission not in gear. Operator's bail not engaging belt or out of
No self-propelling
adjustment. Worn out or broken belt. Broken or mispositioned belt.
Self propelled drive will not
Sticking belt idler arm. Belt fingers out of adjustment, bent or broken.
release
Noisy or broken chain
No chain lubrication. Chain out of alignment or over tensioned.
Engine is locked, will not
Debris locked inside impeller. Engine problem.
pull over.
Engine Service and Warranty
22.1
22.1
22.1
22.1
22.1
Contact your nearest engine manufacturer's autho-
rized servicing dealer.
R
ecord your machine model, serial number
Serial Plate
21 21
21 21
21
and date-of-purchase and where purchased
118 dB
1803 S. Jefferson
Lee's Summit, MO 64063 / USA
(816) 524-9666 (816) 524-6983
Model
Unit (weight)
lbs
Purchase
Purchased
Date
from
Part No. 800012
Reference: Label CAUTION
Part No. 830138
Before Requesting Service Review These Suggestions
Possible Cause
R
P.O. Box 308
Serial No.
Engine Power
kg
h p
BEFORE OPERATING, MAKE SURE:
EXHAUST ELBOW IS ATTACHED.
EXHAUST IS DISCHARGING INTO
ENCLOSED CONTAINER.
HOSE IS ATTACHED.
ALL GUARDS ARE ATTACHED.
OPERATING INSTRUCTION IS OBTAINED.
INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY
WORN AND DAMAGED PARTS.
PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING.
NEVER SERVICE UNIT WITHOUT DISCONNECTING SPARK PLUG WIRE.
USE ONLY A QUALIFIED MECHANIC TO SER VICE THIS MACHINE.
ABRASIVE DEBRIS WILL SHORTEN UNIT LIFE.
Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
Allow air to feed with debris.
Check impeller and replace if required. Check Engine.
Check stop switches, throttle, and gasoline. Connect spark plug wire.
Clean or replace air cleaner. Or contact a qualified service person.
Check transmission gear selection. Check clutch cable
adjustment and belt and chain (See page 11).
Check idler. Idler arm mounting screw may be too tight or too
loose. Check wire belt guide adjustment. Replace if broken. (see
fig. 3 & 4 adjustment on page 11).
See Chain Adjustments on page 11.
See page 5, Contact an engine servicing dealer for engine problems.
22 22
22 22
22
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
kw
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON STREET; LEE'S SUMMIT, MO 64082-2312 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
Page 12 of 12
CAUTION
READ OWNER'S MANUAL
USE PROTECTION
STOP ENGINE AND ALLOW T O
COOL BEFORE REFUELING.
KEEP ENGINE CLEAN OF DEBRIS.
Solution
WARRANTY PROCEDURE
www.billygoat.com
Form No. F021402A
Advertisement
Table of Contents
