Table of Contents
Advertisement
MAINTENANCE
17
Use only a qualified mechanic for any
adjustments, disassembly or any kind
of repair .
WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN
MACHINE OFF, MAKE SURE ALL MOVING PARTS COME
TO A COMPLETE STOP.
DISCONNECT SPARK PLUG WIRE
BEFORE SERVICING UNIT.
ENGINE: See engine manufacturer
operator's instructions.
RECONNECT SPARK PLUG WIRE,
GUARDS, BAG, CAPS AND / OR
HOSE BEFORE STARTING ENGINE.
Maintenance Schedule
17.2
Maintenance Operation
Engine (See Engine Manual)
Check for excessive vibration
Clean Debris Bag
Inspect for loose parts
Inspect for worn or damaged parts
TROUBLESHOOTING
20
Problem
Will not vacuum or has poor vacuum performance. · Dirty or full debris bag or filter.
Abnormal vibration.
Engine w ill not start.
Engine Service and Warranty
22.1
Contact your nearest engine manufacturer's authorized
servicing dealer.
R
ecord your machine model, serial number and
21
Serial Plate
date-of-purchase and where purchased
R
Model
109 dB
Unit(Weight)
lbs.
Purchase
Purchased
from
Date
Part No. 890049
All manuals and user guides at all-guides.com
Follow these hourly
maintenance intervals.
Every
Every 5 hrs
Use
or (Daily)
Before Requesting Service Review These Suggestions
· Nozzle height set too high or too low .
· Hose kit cap missing.
· Clogged nozzle or exhaust.
· Excessive quantity of debris.
· Loose or out of balance impeller.
· Loose engine.
· Throttle in off position.
· Engine not in full choke position.
· Out of gasoline or bad or old gasoline.
· Spark Plug w ire disconnected.
· Gas Valve off.
· Dirty air cleaner.
· Safety Interlock disengaged on bag plate.
1803 S.W. Jefferson
Lee's Summit,
MO 64062 / USA
Tel (816) 524-9666
Fax (816) 524-6983
Serial No.
Engine Power
kg
kW
rpm
min
17.1
IMPELLER REMOVAL
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove engine, impeller and mounting plate by removing nuts
(item 26) around outside of housing.
4. Leaving engine fastened to plate, remove impeller bolt (item 50)
and lock washer and slide impeller off crankshaft ( A puller may be
required).
CAUTION: Do not drop impeller.
5. If impeller does not slide off crankshaft, place two crowbars
between impeller and housing on opposite sides. Pry impeller away
from engine until it loosens. Using a penetrating oil can help loosen
a stuck impeller.
6. If the impeller cannot be loosened, obtain a 1" (25.4mm) longer
bolt of the same diameter and thread type as the impeller bolt.
Invert engine and impeller and support engine above ground to
prevent recoil damage. Thread longer bolt by hand into the
crankshaft until bolt bottoms. Using a suitable gear or wheel puller
against the bolt head and the impeller back-plate (near the blades),
remove impeller from shaft.
7. To reinstall impeller, use a new impeller bolt and lockwasher
8. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N . m).
9. Reinstall engine, impeller, and mounting plate onto housing in
reverse order of removal.
10. Before connecting spark plug wire, slowly pull engine starting
rope to insure that impeller rotates freely.
11. Reinstall spark plug wire.
Possible Cause
· Clean debris bag and filter. Shake bag clean or
w ash.
· Adjust nozzle height.
· Check for hose kit cap.
· Unclog nozzle or exhaust (see page 5)
· Allow air to feed w ith debris.
· Check impeller and replace if required.
· Check Engine.
· Check throttle
· Check throttle, choke position
· Check throttle, choke position and gasoline.
· Connect spark plug w ire.
· Turn on gas valve.
· Clean or replace air cleaner. Contact a qualified
service person.
· Bag not fully engaged or Rod in bag is bent.
22
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
binding.
-1
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON LEE'S SUMMIT, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983
Page 8 of 8
For damaged or imbalanced
impeller
Solution
WARRANTY PROCEDURE
Form No. F100202A
www.billygoat.com
Advertisement
Table of Contents
