Viking 1600-IP Series Product Manual page 9

Dimensions: Overall - 127mm x 127 x
57mm (5.0" x 5.0" x 2.25"), Plastic
Electrical Box - 102mm x 102mm x
54mm (4.0" x 4.0" x 2.14")
Shipping Weight: 1 kg (2.12 lbs.)
Front Panel Material: 14 gauge Marine
grade 316 brushed stainless steel
Connections: Gel-filled butt connectors
* Front View of
Plastic Rough-In
Box (included)
** Wire knock out
(2) Standard flat head
dry wall (sheet rock)
screws (not included)
|
OR
|
5.22"
5.14"
2.25"
Front View of Optional
VE-5x5 (not included)
Optional VE-5x5 Surface Mount Box with black satin powder paint finish, not
included (DOD 424). Optional VE-LIGHT kit can be used to illuminate the faceplate
when used with a VE-5x5 (DOD 428). WARNING: Do NOT use a wet location box.
* Note: The black plastic rough-in box (part # 259576) may be purchased separately (Example: Mounting boxes to studs before the
walls are finished for flush installation). Go to www.vikingelectronics.com and click on "Spare Parts" to order these rough-in boxes.
** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent
condensation from accumulating inside the E-1600-20-IP always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4"
diameter hole in the bottom of the black plastic box.
E-1600-20-IP
Optional Enhanced Weather Protection (EWP) Available: The optional EWP
products feature foam rubber gaskets and boots, sealed connections, gel-filled butt
connectors, as well as urethane or thermal plastic potted circuit boards. See DOD
859.
Mounting with Plastic Rough-In Box (included): Flush into walls, mounts to side
of wall stud. Mounting with Optional VE-5x5: Surface mount to walls, single gang
boxes, double gang boxes, posts, or to a Viking VE-GNP Gooseneck pedestal (see
DOD 424 for more information).
Note: When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply
a bead of clear silicone caulking around the top edge / sides of faceplate or VE-5x5.
Note: When European CE compliance is required, mount in optional VE-5X5
metal enclosure.
4.0"
Condensation
Drain Hole
3.25"
(4) 0.38" diameter
(for gooseneck
pedestal mounting)
(1) 0.74"
diameter
Condensation
Drain Hole
Rear View of Optional
VE-5x5 (not included)
2.1"
Peel paper liner and adhere gasket
to back of panel, centering over
mounting holes. Caution: For rough
surfaces (ie: brick, stucco, etc.)
additional caulking may be required.
P
H E L
I N F O
L
C A L
T E D
N E C
C O N
(2) 0.2 x 0.43 slots for
single gang box
(4) 0.2 x 0.43 slots for
double gang box
The
Mount Box (left) is designed to be
surface mounted to a single gang
3.0" 3.3"
box, double gang box or VE-GNP
Gooseneck Pedestal. For more
information on the VE-5x5 and
3.0"
VE-GNP, see DOD 424.
Important: The E-1600-20-IP will
NOT mount to a standard double
gang box. If your applications
requires a double gang box, see
model E-1600A-22-IP on page 10.
9
(4) T-10 Torx stainless steel,
flat head, security screws
and drive bit (included)
Laser Etched Graphics
Marine grade 316 stainless
steel faceplate and push button
switches (sealed per IP67)
Grade 2 Braille Label
"Help" Push to Call Button
Call Connected Red LED
"Info" Push to Call Button
optional VE-5x5 Surface