Viking 1600-IP Series Product Manual page 14

Note: This is a E-1600-IP board (PCB) only kit. This kit can be used to convert
2008 or newer Viking 1600A Series analog emergency phone to a VoIP version.
A special connector and microphone assembly is required to convert 2007 and
older Viking 1600A Series emergency phones. Contact Viking technicsal
Support if attempting to install this kit in these older phones. The kit can also be
used to replace a damaged "IP" board in the field.
(2) 0.156
diameter
type 2
mounting
holes
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller,
Note: This is a E-1600-IP-EWP board (PCB) only kit. This kit can be used to
convert any Viking 1600A-EWP Series analog emergency phone to a VoIP
version. The kit can also be used to replace a damaged "IP" board in the field.
R32 R32
R62 R62
R59 R59
R11 R11
R12 R12 R34 R34
XTAL 2 XTAL 2
L1 L1
L2 L2
R24 R24
c35 c35
R23 R23
C37 7 C37
R25 R25
C16 6 C16
C25 C25 5
C5 C5
C21 C21
R18 R18
R20 R20
Optional 2 Amp Relay
Output Contacts Connector
Connect to doorstrike,
mag lock, gate controller,
SL-2, LV-1K, etc.
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
FIGURE 1
3.50
3.20
3
SL-2, LV-1K, etc.
Gray (N.C.)
Blue (COM)
Yellow (N.O.)
E-1600-53-IP-EWP
L12 L12
L13 L13
R58 R58
C71 C71 L L7 L7
R53 R53
C58 C58
R55 R55
R54 R54
R65 R65
C55 5 C55
C53 3 C53
C54 C54
- Black
LED
+ Red
Black
Help/Call Switch
Black
Red**
Info Switch
Red**
Yellow
Speaker
Yellow
- Black
Mic
+ Red
E-1600-53-IP
Shipping Weight: .45 kg (1 lb)
Connections: (1) RJ45 10/100 Base-T, (3) optional gel-filled butt
connectors
Note: When European CE compliance is required, mount in a metal
enclosure.
0.15
1.5
1 10 1
Connector and Wires from
Existing Standard (non EWP)
1600A Series Analog
Emergency Phone
Shipping Weight: .45 kg (1 lb)
Connections: (1) RJ45 10/100 Base-T, (13) gel-filled butt connectors
Note: When European CE compliance is required, mount in a metal
enclosure.
Replacing Analog 1600A Series EWP Potted Circuit Boards:
Step 1. Cut wires from J1 (10 pin connector) and J2 (3 pin connector).
Step 2. Remove the two #6 phillips screws fastening the circuit board.
Step 3. Cut off any stripped wire ends from the replacement cable.
Using the supplied gel-filled butt connectors, connect corre-
sponding wires from replacement cable to the previously cut
Step 4. wires from the LED, Help/Call switch, optional Info switch,
Speaker and Microphone. See FIGURE 1 for wire color and
polarity.
** Note: These two red wires are
only used on units with an Info
(optional)
button. When installing on a
single button unit, cut off these
two red wires and discard.
14
2.0
2.63
0.63