Communications Parameters - Toshiba TOSVERT VF-FS1 Instruction Manual

7. Communications parameters

The settings of communication-related parameters can be changed from the operation panel and
the external controller (computer). Note that there are two types of parameters: parameters whose
settings take effect immediately after the setting and parameters whose settings do not take effect
until the inverter is turned back on or reset.
Com-
muni-
cation Title Function
Num-
ber.
Communication
0800
baud rate
0801 Parity
0802 Inverter number
Communication
0803
error trip time
Communication
0805
waiting time
Setting of master
and slave invert-
ers for communi-
0806 cation between
inverters (setting
of master and
slave)
0811 Point 1 setting
0812 Point 1 frequency
0813 Point 2 setting
0814 Point 2 frequency
Selection of
0829 communication
protocol
Number of motor
0856 poles for motor
speed
0870 Block write data 1
0871 Block write data 2
0875 Block read data 1
0876 Block read data 2
0877 Block read data 3
0878 Block read data 4
0879 Block read data 5
0880 Free notes
Block communi-
FA80 ----
cation for LED
Adjustment range
0: 9600bps
1: 19200bps
0: NON (No parity)
1: EVEN (Even parity)
2: ODD (Odd parity)
0-247
0: (disabled)
1-100
0.00-2.00s
0: Slave inverter (0 Hz command issued
in case the master inverter fails)
1: Slave inverter (Operation continued
in case the master inverter fails)
2: Slave inverter (Emergency stop trip-
ping in case the master inverter fails)
3: Master inverter (transmission of fre-
quency commands)
4: Master inverter (transmission of out-
put frequency signals)
0-100
0.0-200.0Hz
0-100
0.0-200.0Hz
0: Toshiba inverter protocol
1: Modbus-RTU protocol
2: Metasys N2 (option)
3: FLN P1 (option)
4: BACnet (option)
1:2pole , 2:4pole .... 8:16pole
0: No selection
1: Command information 1
2: Command information 2
3: Frequency command
4: Output data on the terminal board
5: Analog output for communications
6: Motor speed command
0: No selection
1: Status information
2: Output frequency
3: Output current
4: Output voltage
5: Alarm information
6: PID feedback value
7: Input terminal board monitor
8: Output terminal board monitor
9: VIA terminal board monitor
10: VIB terminal board monitor
11: Output motor speed monitor
0-65535
0:Disable
1:Enable
44
Default
Unit Valid
setting
After re-
- 1
set.
After re-
- 1
set.
1 0 Real time
1s 0 Real time
0.01s 0.00 Real time
After re-
- 0
set.
1% 0 Real time
0.01Hz 0.0 Real time
1% 100 Real time
0.01Hz 60.0 Real time
After re-
- 0
set.
- 1 Real time
After re-
set.
0
-
After re-
set.
- 0
1 0 Real time
- 0 Real time
E6581393
Modbus
Reference
protocol
Enable Section 7.1
Enable Section 7.1
Enable Section 7.2
Enable Section 7.3
Disable Section 7.4
Disable
Chapter 6
Disable
Disable
Section 6.1
Disable
Disable
Enable
Chapter 3
Enable
Enable
Section
5.1.4
Enable
Section
Section
4.1.3
5.1.2
Enable Section 7.5
Section
Disable
8.4.1