Danfoss 5000 Flux Manual page 52

Parameter list VLT 8000 AQUA
PNU Parameter
# description
200 Output frequency range
201 Output frequency low limit, f
202 Output frequency high limit, f
203 Reference site
204 Minimum reference, Ref
205 Maximum reference, Ref
206 Ramp-up time
207 Ramp-down time
208 Automatic ramp-up/down
209 Jog frequency
210 Reference type
211 Preset reference 1
212 Preset reference 2
213 Preset reference 3
214 Preset reference 4
215 Current limit, I
LIM
216 Frequency bypass, bandwidth
217 Frequency bypass 1
218 Frequency bypass 2
219 Frequency bypass 3
220 Frequency bypass 4
221 Warning: Low current, I
222 Warning: High current, I
223 Warning: Low frequency, f
224 Warning: High frequency, f
225 Warning: Low reference, Ref
226 Warning: High reference, Ref
227 Warning: Low feedback, FB
228 Warning: High feedback, FB
1) Sum = Global
2) Preset reference = North America
Changes during operation:
"Yes" means that the parameter can be
changed, while the VLT AFD is in operation. "No"
means that the VLT AFD must be stopped before
a change can be made.
4-Setup:
"Yes" means that the parameter can be
programmed individually in each of the four
setups, i.e. the same parameter can have four
different data values. "No" means that the data
value will be the same in all four setups.
Conversion index:
This number refers to a conversion figure to be
used when writing or reading to or from a VLT
AFD by means of serial communication.
52
VLT ® 5000/5000 Flux/6000 HVAC/8000 AQUA PROFIBUS
Factory setting
0 -120 Hz
0.0 Hz
MIN
60 Hz
MAX
Hand/Auto linked reference
0.000
MIN
60 Hz
MAX
Depends on the unit
Depends on the unit
Enable
10.0 Hz
Sum 1) /Preset reference
0.00 %
0.00 %
0.00 %
0.00 %
1.0 x I [A]
VLT,N
0 Hz
120 Hz
120 Hz
120 Hz
120 Hz
0.0 A
LOW
I
HIGH VL T,MAX
0.0 Hz
LOW
120.0 Hz
HIGH
999,999.999
LOW
999,999.999
HIGH
999,999.999
LOW
999,999.999
HIGH
Range Changes 4-Setup
during operation
0 - 1000 Hz No
0.0 - f Yes
MAX
f - par. 200 Yes
MIN
Yes
0.000-par. 100 Yes
par. 100-999.999,999 Yes
1 - 3600 Yes
1 - 3600 Yes
Yes
0.0 - par. 100 Yes
2) Yes
-100.00 - 100.00 % Yes
-100.00 - 100.00 % Yes
-100.00 - 100.00 % Yes
-100,00 - 100,00 % Yes
0,1-1,1 x I [A] Yes
VLT,N
0 - 100 Hz Yes
0.0 - par. 200 Yes
0.0 - par. 200 Yes
0.0 - par. 200 Yes
0.0 - par. 200 Yes
0.0 - par. 222 Yes
Par. 221 - I Yes
VLT,MAX
0.0 - par. 224 Yes
Par. 223 - par. 200/202 Yes
-999,999.999 - par. 226 Yes
Par. 225 - 999,999.999 Yes
-999,999.999 - par. 228 Yes
Par. 227 - 999,999.999 Yes
Conversion index
74
2
1
0
-1
-2
-3
-4
Data type:
Data type shows the type and length of the telegram.
Data type
Description
3
4
5
6
7
9
MG.90.D1.02 – VLT is a registered Danfoss trademark
Data
Conversion
type
index
0
5
Yes
-1
6
Yes
-1
6
Yes
0
5
Yes
-3
4
Yes
-3
4
Yes
0
7
Yes
0
7
Yes
0
5
Yes
-1
6
Yes
0
5
Yes
-2
3
Yes
-2
3
Yes
-2
3
Yes
-2
3
Yes
-1
6
Yes
0
6
Yes
-1
6
Yes
-1
6
Yes
-1
6
Yes
-1
6
Yes
-1
6
Yes
-1
6
Yes
-1
6
Yes
-1
6
Yes
-3
4
Yes
-3
4
Yes
-3
4
Yes
-3
4
Yes
Conversion factor
0.1
100
10
1
0.1
0.01
0.001
0.0001
Integer 16
Integer 32
Unsigned 8
Unsigned 16
Unsigned 32
Text string