Danfoss 5000 Flux Manual page 47

Parameter list VLT 6000
PNU Parameter
# description
300 Terminal 16 Digital input
301 Terminal 17 Digital input
302 Terminal 18 Digital input
303 Terminal 19 Digital input
304 Terminal 27 Digital input
305 Terminal 29 Digital input
306 Terminal 32 Digital input
307 Terminal 33 Digital input
308 Terminal 53, analogue
input voltage
309 Terminal 53, min. scaling
310 Terminal 53, max. scaling
311 Terminal 54, analogue
input voltage
312 Terminal 54, min. scaling
313 Terminal 54, max. scaling
314 Terminal 60, analogue input
current
315 Terminal 60, min. scaling
316 Terminal 60, max. scaling
317 Time out
318 Function after time out
319 Terminal 42, output
320 Terminal 42, output,
pulse scaling
321 Terminal 45, output
322 Terminal 45, output,
pulse scaling
323 Relay 1, output function
324 Relay 01, ON delay
325 Relay 01, OFF delay
326 Relay 2, output function
327 Pulse reference,
max. frequency
328 Pulse feedback, max. frequency
Changes during operation:
"Yes" means that the parameter can be changed,
while the VLT frequency converter is in operation.
"No" means that the VLT frequency converter must
be stopped before a change can be made.
4-Setup:
"Yes" means that the parameter can be
programmed individually in each of the four setups,
i.e. the same parameter can have four different data
values. "No" means that the data value will be the
same in all four setups.
Conversion index:
This number refers to a conversion figure to be used
when writing or reading to or from a VLT frequency
converter by means of serial communication.
MG.90.D1.02 – VLT is a registered Danfoss trademark
VLT ® 5000/5000 Flux/6000 HVAC/8000 AQUA PROFIBUS
Factory setting
Reset
Freeze output
Start
Reversing
Coasting stop, inverse
Jog
No operation
No operation
Reference
0.0 V
10.0 V
No operation
0.0 V
10.0 V
Reference
4.0 mA
20.0 mA
10 sec.
Off
⇒ 0-20 mA
0 - I
MAX
5000 Hz
⇒ 0-20 mA
0 - f
MAX
5000 Hz
Alarm
0.00 sec.
0.00 sec.
Running
5000 Hz
25000 Hz
Conversion index
Data type:
Data type shows the type and length of the
telegram.
Data type
3
4
5
6
7
9
Range Changes 4-Setup
during operation
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
0.0 - 10.0 V Yes Yes
0.0 - 10.0 V Yes Yes
Yes Yes
0.0 - 10.0 V Yes Yes
0.0 - 10.0 V Yes Yes
Yes Yes
0.0 - 20.0 mA Yes Yes
0.0 - 20.0 mA Yes Yes
1 - 99 sec. Yes Yes
Yes Yes
Yes Yes
1 - 32000 Hz Yes Yes
Yes Yes
1 - 32000 Hz Yes Yes
Yes Yes
0 - 600 sec. Yes Yes
0 - 600 sec. Yes Yes
Yes Yes
Depends on Yes Yes
input terminal
0 - 65000 Hz Yes Yes
Conversion factor
74
2
1
0
-1
-2
-3
-4
Description
Integer 16
Integer 32
Unsigned 8
Unsigned 16
Unsigned 32
Text string
Conversion
Data
index
type
0
5
0
5
0
5
0
5
0
5
0
5
0
5
0
5
0
5
-1
5
-1
5
0
5
-1
5
-1
5
0
5
-4
5
-4
5
0
5
0
5
0
5
0
6
0
5
0
6
0
5
0
6
0
6
0
5
0
6
0
6
0.1
100
10
1
0.1
0.01
0.001
0.0001
47