Revision History - Landis+Gyr E350 Series User Manual

2/56

Revision History

Version Date
a 24.07.2009
b 18.01.2010
c 05.05.2010
d 24.08.2010
e, f 06.09.2010
g 16.10.2010
h 09.12.2010
k 17.03.2011
m 01.06.2011
n 20.12.2011
p 24.10.2012
q 20.12.2012
r 31.01.2016
© Landis+Gyr
Comments
First edition.
Example absolute value summation corrected, channel configuration table updated
with OBIS codes and remarks, instantaneous power accuracy added, new section
2.4 "Radio Interference", description of power-up display corrected, range of CDS
and NDS display durations corrected, description of error display changed, meter
display list updated (without display text), description of optical interface enhanced,
description of manufacturer specific mode C-C added, description of optical test
outputs enhanced, minor formatting and text improvements.
New display list items, Combined sum integrated in channel configuration (section
1.6); Summation modes updated, FW version presentation updated, supply control
switch tamper added, More detailed explanation of supply control switch icon, table
of required measuring times updated, display status messages added, error code
and status flag explanations extended, addressability added, advice (restriction) for
FW version <= M23 added, availability for supply control switch added.
"Meter display list" corrected (voltage, current, frequency, power items);
Explanation efficiency registers updated; Table Instantaneous Values updated;
Display status messages updated; Meter tools added.
Minor formatting and text improvements.
Updating 1.8. Instantaneous values.
Section 5.2.5 Display sequence entirely updated (main and service display).
Declaration of conformity replaced.
Note about restrictions for meters with firmware versions M21 to M23 added in
section 1.2 "Purpose of use". Section 1.3 "Advice" deleted (integrated into note in
section 1.2).
Section 1.4 "Characteristic" expanded with remark about ZFF100 meters phase fail
behaviour; Section 2.3 "Safety Instructions" expanded with remark, that PE must
not be switched with supply control switch and only "useful" tool have to be used;
Section 5.2.7 "Error Display" modified; Remark about module data added in section
5.2.9; Content of section 5.2.12 "Error descriptions E350 Series 1 and Series 2"
moved partly into functional description and partly to section 6.2 "Error Codes":
Safety information about cleaning added in section 6.1 and modified in section 7.2.;
Terminology changes: breaker  disconnector, baud rate  transmission rate,
baud  bps (bits per second); Minor formatting and text improvements.
Section 1.6.3: Adapted to firmware version M25 (8 measurement channels)
Section 5.2.9: New display item: Supply control switch tamper counter.
Adapted to firmware version M26 (DSMR 4.0):
"Introduction" updated.
Section 5.2.2 "Explanation of LCD Elements" updated.
Section 5.2.4 "Display Definitions" updated.
Section 5.2.5 "Display Sequence" entering and exiting "Service Display" updated.
Section 5.2.6 "Display Check" updated.
Section 5.2.9 "Meter Display List – Available Items with OBIS Codes" updated.
Section 5.4 "Optical Interface" updated (added blocking).
Section 5.5.5 "Readout Status Flag (C.5.0)" updated.
New section 5.5.4 "Display Status Flag (C.5.0)" added.
New section 5.6 "Password Lock-out" added.
Section 7.1.1 "Higher Register Resolution" updated.
Section 7.1.2: Note about test time for register test for meters with firmware version
M25.
Section 1.2: Note about restriction for meters with firmware version M25.
Added "For indoor use only" notification in section 4.1 "Mounting the Meter".
D000027979 en t – E350 Series 2, 3-Phase ZxF100Ax/Cx – User Manual
Revision History