Application Diagram - Extron electronics DTP T DSW 4K Series User Manual

•
•
•
•
•
•
•
•
•
•

Application Diagram

The diagram below shows a typical application for the DTP T DSW 4K 333.
Extron
DTP T DSW 4K 333
Transmitter
OVER TP
POWER SIG LINK
1 2 3
12V HDBT
--A MAX AUDIO
RS-232 IR CONTACT IN
DTP
INPUTS RGB, YUV HDMI DP OUT Tx Rx G Tx Rx 1 2 3 G
DisplayPort
PC
HDMI
Blu-Ray
RGB
Laptop
Figure 1.
DTP output is compatible with HDBaseT‑enabled devices — The DTP output
can be configured to send video and embedded audio, plus bidirectional RS-232 and
unidirectional IR signals to an HDBaseT-enabled display.
Accepts additional analog stereo audio signals — The DTP T DSW 4K series
accepts stereo analog audio signals for simultaneous transmission over the same
shielded twisted pair cable.
Bidirectional RS‑232 and IR pass‑through for AV device control — Bidirectional
RS-232 control and IR signals can be transmitted alongside the video signal, allowing
remote AV devices to be controlled without the need for additional cabling.
HDCP compliant — Ensures display of content-protected media and interoperability
with other HDCP-compliant devices.
Supports DisplayPort SST — Single Stream Transport data rates up to 10.8 Gbps
Supported HDMI specification features include data rates up to 10.2 Gbps,
Deep Color up to 12‑bit, 3D, and HD lossless audio formats
Digital conversion of analog input signals — Analog video signals up to 1920x1200
are digitized, ensuring that a reliable, high quality digital video signal is sent to the output
destination.
RS‑232 control port — Enables the use of serial commands for integration into
a control system. Extron products use the SIS - Simple Instruction Set command
protocol, a set of basic ASCII commands that allow for quick and easy programming.
Contact closure remote control with tally output — Allows for remote selection of
an input channel, while a tally output provides +5 VDC to light an LED to indicate the
currently selected input.
Compatible with all DTP 230 and 330 Series receivers and DTP 230‑ and
330‑enabled products — Enables mixing and matching with desktop and wallplate
receivers, as well as other DTP 230- and 330-enabled products to meet application
requirements.
IN1608
INPUTS
1 2 3 4 5 6 7 8
CONFIG
REMOTE
TALLY OUT RS-232
Extron
1 2 3 +V Tx Rx G
INPUTS
OVER DTP
RS-232 IR
1
3 5
7
Tx Rx G Tx Rx 8
SIG LINK SIG
CONFIGURABLE OVER DTP
100-240V ~ -- A MAX 2
HDMI HDMI RS-232 IR
4 6
DTP IN Tx Rx G Tx Rx DTP IN
50/60 Hz
XTP DTP 24 Cable
330'
DTP T DSW 4K 333 Application Diagram
INPUTS OUTPUTS
MENU
SIGNAL
1 2 3 4 5 6 7 8 A B C
HDCP
ENTER
SCALING PRESENTATION SWITCHER SCALING PRESENTATION SWITCHER
IPCP 505
IN1608 SA
AMPLIFIED OUTPUT AMPLIFIED OUTPUT
2x25W(8 2x25W(8
L L
OUTPUTS AUDIO INPUTS OUTPUTS
L 1 R L 3 R L 5 R 1 2
CLASS 2 WIRING CLASS 2 WIRING
C A REMOTE REMOTE
IPCP 505
COM
LINK SIG LINK +48V LAN LAN
OVER DTP MIC/LINE VARIABLE
SWITCHED
RS-232 IR HDMI L 2 R L 4 R L 6 R 2 L R RESET RESET RS-232 RS-232 12VDC
B
1 2 LIMIT
+48V R TX
Tx Rx G Tx Rx DTP OUT Tx Rx Tx Rx G G
RX
3 4 OVER 1 2 3 4 5
DTP HDMI 330 Rx
SIG LINK
POWER
12V
0.7A MAX
DTP IN
Extron DTP T DSW 4K Series • Introduction
RTS
FLEX 100
IR/S RELAY I/O eBUS
CTS
1 2 3 4 1 2 3 4 1 2 ACT LIMIT LINK
TX
IR
RX ACT
6 7 8 5 6 7 8 5 6 7 8 3 4 OVER
TLP 1000TV
Ethernet
OUTPUTS
AUDIO
L R
HDMI
Projector
2