Table of Contents
Advertisement
5 PROGRAMMING BASIC INSTRUCTIONS
5.1 PARAMETER STRUCTURE
Aiming at simplifying the parameterization process, the CFW500 parameters were classified into ten groups which
can be individually selected in the Menu area of the HMI display. When the enter/menu key of the HMI is pressed in
the monitoring mode, you enter the setting mode level 1. In this mode, it is possible to select the desired parameter
group by browsing with the "
AND BASIC PROGRAMMING on page
NOTE!
The inverter comes from the factory with the frequency (V/f 50/60 Hz mode) and voltage adjusted
according to the market.
The reset to factory default may change the content of the parameters related to frequency as per
P0204. In the detailed description, some parameters have values between brackets, which represents
the default value for operation in 50 Hz; thus the value without brackets is the default for operation
in 60 Hz.
5.2 PARAMETERS SELECTED BY THE HMI MENU
In the first level of the setting mode, select the group to browse the next levels according to the table below.
Group
PARAM
All parameters.
Read only parameters:
P0001, P0002, P0003, P0004, P0005, P0006, P0007, P0009, P0011, P0012, P0013, P0014, P0015, P0016, P0017,
P0018, P0019, P0020, P0021, P0022, P0023, P0024, P0027, P0029, P0030, P0037, P0040, P0041, P0047, P0048,
READ
P0049, P0050, P0051, P0052, P0053, P0054, P0055, P0060, P0061, P0062, P0063, P0064, P0065, P0070, P0071,
P0072, P0073, P0074, P0075, P0295, P0296, P0316, P0680, P0681, P0682, P0683, P0685, P0690, P0695, P0696,
P0697, P0698, P0705, P0706, P0707, P0708, P0709, P0719, P0720, P0721, P0722, P1000, P1002.
MODIF
Only parameters whose contents are different from the factory settings.
Parameters for simple application: ramps, minimum and maximum speed, maximum current and torque boost:
BASIC
P0100, P0101, P0133, P0134, P0135 and P0136.
Parameter related to the motor data control:
MOTOR
P0135, P0136, P0137, P0138, P0150, P0151, P0152, P0153, P0156, P0157, P0158, P0178, P0399, P0400, P0401,
P0402, P0403, P0404, P0407, P0409.
Groups related to digital and analog inputs and outputs:
P0012, P0013, P0014, P0015, P0016, P0017, P0018, P0019, P0020, P0021, P0022, P0105, P0220, P0221, P0222,
P0223, P0224, P0225, P0226, P0227, P0228, P0229, P0230, P0231, P0232, P0233, P0234, P0235, P0236, P0237,
I/O
P0238, P0239, P0240, P0241, P0242, P0243, P0244, P0245, P0246, P0247, P0248, P0249, P0250, P0251, P0252,
P0253, P0254, P0255, P0256, P0257, P0258, P0259, P0260, P0263, P0264, P0265, P0266, P0267, P0268, P0269,
P0270, P0271, P0275, P0276, P0277, P0278, P0279, P0287, P0288, P0290, P0293, P0533, P0535.
Parameter related to the communication networks:
P0308, P0310, P0311, P0312, P0313, P0314, P0316, P0680, P0681, P0682, P0683, P0684, P0685, P0690, P0695,
NET
P0696, P0697, P0698, P0700, P0701, P0702, P0703, P0705, P0706, P0707, P0708, P0709, P0710, P0711, P0712,
P0713, P0714, P0715, P0716, P0717, P0718, P0719, P0720, P0721, P0722, P0740 ... P0968.
Parameter to configure the HMI:
HMI
P0200, P0205, P0206, P0207, P0208, P0209, P0210, P0213, P0216, P0528, P0529.
Parameter related to the SoftPLC function:
SPLC
P1000, P1001, P1002, P1010..P1059.
Parameter to enter the V V W - Oriented Start-up mode:
STARTUP
P0202, P0399, P0400, P0401, P0402, P0403, P0404, P0407, P0408, P0409.
NOTE!
Besides the selected group in the menu field of the HMI, the view of the parameters on the HMI depends
on the hardware installed and on the operating mode of the CFW500. Therefore, observe the connected
plug-in module, as well as the motor control mode: V V W or V/f. For example, if the plug-in module only
features the analog input AI1, the parameters related to the other analog inputs are not shown. The
same occurs with the parameters exclusively related to the V V W and V/f modes.
" and "
" keys. For further details on the use of the HMI, refer to
4-1.
Table 5.1: Parameter group accessed by the HMI MENU
Contained Parameters
Programming Basic Instructions
Chapter 4 HMI
5
CFW500 | 5-1
Hide quick links:
Advertisement
Table of Contents
