Log Set Installation - Vermont Castings Radiance RADVT Series Installation & Operating Manual

24 in. min.
(508 mm)
(610 mm)
Lowest
Discharge
Opening
Termination
Cap
Storm Collar
Roof
Flashing
Roof Pitch H (Min.) Ft.
Flat to 6/12 1.0*
Roof Pitch H (Min.) Ft.
Flat to 6/12 1.0*
Over 6/12 to 7/12 1.25*
Over 6/12 to 7/12 1.25*
Over 7/12 to 8/12 1.5*
Over 7/12 to 8/12 1.5*
Over 8/12 to 9/12 2.0*
Over 8/12 to 9/12 2.0*
Over 9/12 to 10/12 2.5
Over 9/12 to 10/12 2.5
Over 10/12 to 11/12 3.25
Over 10/12 to 11/12 3.25
* 3 ft. minimum in snow regions
* 3 Feet. Minimum in Snow Regions
Figure 3.18 - Minimum Height from Roof to Lowest Discharge
Opening
D. Log Set Installation
Before beginning log installation, remove stove front and
glass frame. Refer to Figures 3.19 and 3.20.
Note: Remove the safety barrier before you remove the
glass frame. To remove the barrier, simply lift up and pull
out until the tabs are clear of their corresponding slots
on the firebox. Then proceed to remove the glass frame
by following the steps below.
Figure 3.19 - Remove the safety barrier and stove front.
2121
Horizontal
overhang
20 in.
Vertical
wall
X
12
Roof Pitch
is X / 12
H (min.) - Minimum height
from roof to lowest
discharge opening.
Roof Pitch H (Min.) Ft.
Over 11/12 to 12/12
Roof Pitch H (Min.) Ft.
Over 11/12 to 12/12 4.0
Over 12/12 to 14/12
Over 12/12 to 14/12 5.0
Over 14/12 to 16/12
Over 14/12 to 16/12 6.0
Over 16/12 to 18/12
Over 16/12 to 18/12 7.0
Over 18/12 to 20/12 7.5
Over 18/12 to 20/12
Over 20/12 to 21/12 8.0
Over 20/12 to 21/12
ST139
Radiance
remove front
4/20/01 djt
Vermont Castings • Radiance RADVT Installation Manual_R4 • 04/19
Figure 3.20 - Release the latches to remove the glass frame.
4.0
5.0
6.0
7.0
7.5
A barrier designed to reduce the risk of burns from
8.0
the hot viewing glass is provided with this
appliance and shall be installed.
Before installation, inspect ember bed burner for damage.
Do not use ember bed if damaged or cracked. Small, shallow
surface cracks are acceptable.
1. Remove the logs from their packaging and inspect each
piece for damage. DO NOT INSTALL DAMAGED LOGS.
2. Install the rear log by placing it on the ember bed toward
the back of the firebox, Figure 3.21. The log should touch
the back wall of the firebox. When the log is in place, the
two (2) notches on the bottom of the log rest on the two
(2) ribs on the back side of the ember bed, Figure 3.22.
Une barrière visant à réduire le risque de brûlure
par le hublot chaude est fournie avec cet
Figure 3.21 - Rear Log
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
DANGER
Un panneau vitré chaud peut
causer des brûlures.
Laissez refroidir le panneau
vitré avant d'y toucher.
Ne laisser jamais les enfants
toucher le panneau vitré.
appareil et doit être installé.
LG488
rear log
6/07
S T141
pull glass lat
10/ 99
Rear Log
3-90-30007498