System; Splman - Canon D1300 Series Service Manual

■ SYSTEM

COPIER > FUNCTION > SYSTEM
PANEL-UP Download from USB memory (PANEL)
Details To perform downloading when PANEL exists in the root directory of the
USB memory.
Use case At upgrade
Adj/set/operate method 1) Install the USB memory.
2) Select the item, and then press OK key.
3) Turn OFF/ON the main power switch.
Caution Do not turn OFF/ON the power before "Executing..." disappears.
Related service mode COPIER> FUNCTION> SYSTEM> DOWNLOAD, BKUP-UP
BKUP-UP Download from USB memory (BKUP)
Details To perform downloading when BKUP exists in the root directory of the
USB memory.
Use case At upgrade
Adj/set/operate method 1) Install the USB memory.
2) Select the item, and then press OK key.
3) Turn OFF/ON the main power switch.
Caution Do not turn OFF/ON the power before "Executing..." disappears.
Related service mode COPIER> FUNCTION> SYSTEM> PANEL-UP
LOGWRITE Writing sublog to USB memory
Details To write sublog that includes the following information to the USB
memory.
• Job list (job names, user names, and destinations)
• Communications log (destinations and user names)
• Job log (user names and job names)
Use case When analyzing the cause of a problem
Adj/set/operate method 1) Install the USB memory.
2) Select the item, and then press OK key.
3) Turn OFF/ON the main power switch.
Caution Do not turn OFF/ON the power before "Executing..." disappears.
IMPORT Reading of service mode setting value from USB memory
Details To write the service mode setting values (excluding those related to
Reader/ADF) to the USB memory.
Use case When replacing the Main Controller PCB as a measure against failures
Adj/set/operate method 1) Install the USB memory.
2) Select the item, and then press OK key.
3) Turn OFF/ON the main power switch.
Caution Do not turn OFF/ON the power before "Executing..." disappears.
EXPORT Writing service mode setting value to USB memory
Details To write the service mode setting values (excluding those related to
Reader/ADF) to the USB memory.
Use case When replacing the Main Controller PCB as a measure against failures
Adj/set/operate method 1) Install the USB memory.
2) Select the item, and then press OK key.
Caution "Executing..." disappears when writing is completed.
8
Service Mode > COPIER > FUNCTION > SPLMAN
T-8-13
8 Service Mode > COPIER > FUNCTION > SPLMAN

■ SPLMAN

COPIER > FUNCTION > SPLMAN
SPL14159 Fixing of USB device ID
Details To fix the USB device ID to "000000000000".
Driver for each machine is installed to a PC. However, by fixing the
serial number, the PC considers that any connected machine to be
the same machine; thus, there will be no need to install the drivers
many times.
Adj/set/operate method 1) Enter the value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SPL65677 Increase of paper leading edge margin
Details To increase the margin on the leading edge of paper.
As the value is incremented by 1, the margin is increased by 0.1 mm.
If the setting is incompatible with SPL68676 (decrease of margin), the
setting is disabled (the margin will be standard).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL68676
SPL68676 Decrease of paper leading edge margin
Details To decrease the margin on the leading edge of paper.
As the value is incremented by 1, the margin is decreased by 0.1 mm.
If the setting is incompatible with SPL65677(increase of margin), the
setting is disabled (the margin will be standard).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL65677
SPL68677 Increase of paper right and left margins
Details To increase the margins on the right and left edges of paper.
As the value is incremented by 1, the margin is increased by 0.1 mm.
If the setting is incompatible with SPL25607 (decrease of margins),
the setting is disabled (the margins will be standard).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Unit 0.1 mm
Default value 0
Related service mode COPIER> FUNCTION> SPLMAN> SPL25607
8-15
8-15