Feed-Adj - Canon D1300 Series Service Manual

■ FEED-ADJ

COPIER > ADJUST > FEED-ADJ
ADJ-C1 Cassette1 write start pstn in horz scan
Details To adjust the image write start position in the horizontal scanning
direction when picking up paper from the Cassette 1 (standard
Pickup Cassette).
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.25 mm.
+: Left margin becomes larger (An image moves to the right.)
-: Left margin becomes smaller (An image moves to the left.)
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -9 to 9 (-2.22 to +2.22 mm)
Unit Approx. 0.25 mm
Default value -2
ADJ-C2 Cassette2 write start pstn in horz scan
Details To adjust the image write start position in the horizontal scanning
direction when picking up paper from the Cassette 2 (option Pickup
Cassette).
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.25 mm.
+: Left margin becomes larger (An image moves to the right.)
-: Left margin becomes smaller (An image moves to the left.)
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -9 to 9 (-2.22 to +2.22 mm)
Unit Approx. 0.25 mm
Default value -4
8
Service Mode > COPIER > ADJUST > FEED-ADJ
8 Service Mode > COPIER > ADJUST > FEED-ADJ
COPIER > ADJUST > FEED-ADJ
ADJ-MF Write start position in the horizontal scanning direction at pickup from
the Multi-purpose Tray
Details To adjust the image write start position in the horizontal scanning
direction when picking up paper from the Multi-purpose Tray.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.25 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -9 to 9 (-2.22 to +2.22 mm)
Unit Approx. 0.25 mm
Default value -2
ADJ-REFE Write start position in the horizontal scanning direction at 2-sided
pickup
Details To adjust the image write start position in the horizontal scanning
direction at 2-sided pickup.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.25 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -9 to 9 (-2.22 to +2.22 mm)
Unit Approx. 0.25 mm
Default value 0
8-12
T-8-8
8-12