Canon D1300 Series Service Manual page 147

COPIER > ADJUST > CCD
50DF-GB Color displacement (G and B lines) correction value in the vertical
scanning direction at ADF reading (50 %)
Details To correct the color displacement (G and B lines) in the vertical
scanning direction at 50% ADF reading.
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -512 to 512
Unit 0.001 line
Default value 333
Supplement/memo 50 % reading: 300 dpi in horizontal scanning direction x 600 dpi in
vertical scanning direction reading mode.
100DF-RG Color displacement (R and G lines) correction value in the vertical
scanning direction at ADF reading (100 %)
Details To correct the color displacement (R and G lines) in the vertical
scanning direction at 100% ADF reading.
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -512 to 512
Unit 0.001 line
Default value -333
Supplement/memo 100 % reading: 600 dpi in horizontal scanning direction x 600 dpi in
vertical scanning direction reading mode.
8
Service Mode > COPIER > ADJUST > CCD
8 Service Mode > COPIER > ADJUST > CCD
COPIER > ADJUST > CCD
100DF-GB Color displacement (G and B lines) correction value in the vertical
scanning direction at ADF reading (100 %)
Details To correct the color displacement (G and B lines) in the vertical
scanning direction at 100% ADF reading.
When replacing the Main Controller PCB, enter the value of service
label.
Use case When replacing the Main Controller PCB
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -512 to 512
Unit 0.001 line
Default value 333
Supplement/memo 100 % reading: 600 dpi in horizontal scanning direction x 600 dpi in
vertical scanning direction reading mode.
OFST-BW0 Adjustment of CIS (Rear) at B&W reading
Details To adjust the offset of the CIS (Rear) when reading B&W original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 138
Related service mode COPIER>FUNCTION>CCD>BW-AGC
OFST-BW1 Adjustment of CIS (Center) at B&W reading
Details To adjust the offset of the CIS (Center) when reading B&W original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 138
Related service mode COPIER>FUNCTION>CCD>BW-AGC
OFST-BW2 Adjustment of CIS (Front) at B&W reading
Details To adjust the offset of the CIS (Front) when reading B&W original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 138
Related service mode COPIER>FUNCTION>CCD>BW-AGC
OFST-CL0 Adjustment of CIS (Rear) at color reading
Details To adjust the offset of the CIS (Rear) when reading color original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 138
Related service mode COPIER>FUNCTION>CCD>CL-AGC
8-10
8-10