Canon D1300 Series Service Manual page 148

COPIER > ADJUST > CCD
OFST-CL1 Adjustment of CIS (Center) at color reading
Details To adjust the offset of the CIS (Center) when reading color original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 138
Related service mode COPIER>FUNCTION>CCD>CL-AGC
OFST-CL2 Adjustment of CIS (Front) at color reading
Details To adjust the offset of the CIS (Front) when reading color original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 138
Related service mode COPIER>FUNCTION>CCD>CL-AGC
GAIN-BW0 Adjustment of gain at B&W reading
Details To adjust the gain when reading B&W original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 54
Related service mode COPIER>FUNCTION>CCD>BW-AGC
GAIN-CL0 Adjustment of gain at color reading
Details To adjust the gain when reading color original.
Use case When replacing the CIS Unit
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 255
Default value 84
Related service mode COPIER>FUNCTION>CCD>CL-AGC
LED-BW-R Adjustment of LED light-up time (R) at B&W reading
Details To adjust the red color LED light-up time when reading B&W original.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2168
Default value 1000
Related service mode COPIER>FUNCTION>CCD>CL-AGC
LED-BW-G Adjustment of LED light-up time (G) at B&W reading
Details To adjust the green color LED light-up time when reading B&W
original.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2168
Default value 1000
Related service mode COPIER>FUNCTION>CCD>BW-AGC
8
Service Mode > COPIER > ADJUST > PASCAL
8 Service Mode > COPIER > ADJUST > PASCAL
COPIER > ADJUST > CCD
LED-BW-B Adjustment of LED light-up time (B) at B&W reading
Details To adjust the blue color LED light-up time when reading B&W
original.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2168
Default value 1000
Related service mode COPIER>FUNCTION>CCD>BW-AGC
LED-CL-R Adjustment of LED light-up time (R) at color reading
Details To adjust the red color LED light-up time when reading color original.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2168
Default value 1100
Related service mode COPIER>FUNCTION>CCD>BW-AGC
LED-CL-G Adjustment of LED light-up time (G) at color reading
Details To adjust the green color LED light-up time when reading color
original.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2168
Default value 1100
Related service mode COPIER>FUNCTION>CCD>BW-AGC
LED-CL-B Adjustment of LED light-up time (B) at color reading
Details To adjust the blue color LED light-up time when reading color
original.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2168
Default value 1100
Related service mode COPIER>FUNCTION>CCD>BW-AGC
■ PASCAL
COPIER > ADJUST > PASCAL
OFST-P-K Bk density adj at test print reading
Details To adjust the offset of Bk color test print reading signal at Auto Adjust
Gradation (Full Adjust).
When replacing the Main Controller PCB, enter the value of service
label.
As the greater value is set, the image after adjustment gets darker.
Use case • When replacing the ADF/Reader Unit
• When replacing the Main Controller PCB
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -32 to 32
Default value 0
8-11
T-8-6
T-8-7
8-11