Canon D1300 Series Service Manual page 135

Error Code
E Detail Item
Code Code
E000 0000 Title Error in temperature rising of Fixing Assembly
Detection Temperature of the Fixing Assembly did not reach a certain temperature
description within the specified period of time.
Remedy 1. Check the connector between the Fixing Assembly and the DC
Controller PCB.
2. Replace the Fixing Assembly.
3. Replace the Engine Controller PCB.
E001 0000 Title Abnormal high temperature of Fixing Assembly
Detection It was detected that the temperature of the Fixing Assembly was
description abnormally high.
Remedy 1. Check the connector between the Fixing Assembly and the DC
Controller PCB.
2. Replace the Fixing Assembly.
3. Replace the Engine Controller PCB.
E003 0000 Title Abnormal low temperature of Fixing Assembly
Detection It was detected that the temperature of the Fixing Assembly was
description abnormally low.
Remedy 1. Check the connector between the Fixing Assembly and the DC
Controller PCB.
2. Replace the Fixing Assembly.
3. Replace the DC Controller PCB.
E004 0000 Title Error in fixing power supply drive circuit
Detection Failed to detect the zero cross signal for the specified period of time or
description more.
Remedy 1. Check the connection of connector between the Fixing Assembly and
the Engine Controller PCB.
2. Replace the Fixing Assembly.
3. Replace the Engine Controller PCB.
E014 0000 Title Error in startup of the Main Motor
Detection Revolution of the Main Motor did not reach the specified value.
description
Remedy 1. Check the connection of connector between the Main Motor and the
Engine Controller PCB.
2. Replace the Main Motor.
3. Replace the Engine Controller PCB.
E100 0000 Title Laser Scanner Assembly error
Detection At the Laser Scanner Unit, BD cycle was not within the specified range.
description
Remedy 1. Check the connection of connector between the Main Controller PCB
and the Laser Scanner Unit.
2. Check the connection of connector between the Relay PCB and the
Laser Scanner Unit.
3. Replace the Laser Scanner Unit.
7
Error Codes > Error Code
Description
7 Error Codes > Error Code
E Detail Item
Code Code
E196 1000 Title Main Controller PCB reading/writing error
Detection Error in reading/writing of main program in the Main Controller PCB
description
Remedy 1. Install the set of the controller firmware.
2. Replace the Main Controller PCB.
E196 2000 Title Main Controller PCB reading/writing error
Detection Error in reading/writing of setting values storage area in the Main
description Controller PCB
Remedy 1. Install the set of the controller firmware.
2. Replace the Main Controller PCB.
E202 0001 Title CIS Unit HP error (outward)
Detection CIS Unit did not move to HP even it moved backward.
description Reader HP Sensor error, Reader Motor error, CIS Unit error
Remedy 1. Replace the Reader HP Sensor.
2. Replace the Reader Motor.
3. Replace the CIS Unit.
4. Replace the Reader Unit.
E202 0002 Title CIS Unit HP error (homeward)
Detection CIS Unit did not move to HP even it moved forward.
description Reader HP Sensor error, Reader Motor error, CIS Unit error
Remedy 1. Replace the Reader HP Sensor.
2. Replace the Reader Motor.
3. Replace the CIS Unit.
4. Replace the Reader Unit.
E248 0001 Title Error in access to backup data for Reader (reading error at power-on)
Detection The Reader-related adjustment values could not be read.
description
Remedy 1. Clear the backup RAM of RCON.
Execute COPIER>FUNCTION>CLEAR>RCON.
2. Enter all the values written on the service label in service mode
again.
3. Turn OFF and then ON the main power.
E351 0000 Title System error
Detection System error.
description
Remedy 1. Install the set of the controller firmware.
2. Replace the Main Controller PCB.
E733 0000 Title Printer communication error
Detection Communication error between the Engine Controller PCB and the Main
description Controller PCB occurred.
Remedy 1. Check the connection of connector between the Engine Controller
PCB and the Main Controller PCB.
2. Install the set of the controller firmware.
3. Replace the Main Controller PCB.
4. Replace the Engine Controller PCB.
7-3
Description
7-3