Related Manuals for Body Solid Powerline PLA1000
Summary of Contents for Body Solid Powerline PLA1000
- Page 1 PLA1000 POWER RACK LAT ATTACHMENT Owner’s Manual WWW.BODYSOLID.COM V PLA1000-092018...
- Page 2 Do not allow the machine to be used until damaged or worn cables are replaced. Using or allowing a machine to be used with a suspect cable can result in serious injury. See Owner’s Manual for more information. For Body-Solid Customer Service Call 1-800-556-3113...
-
Page 3: Table Of Contents
PLA1000 TABLE OF CONTENTS • SAFETY INSTRUCTIONS....... PAGE 4 • PREPARATION........PAGE 5 • PART/HARDWARE LIST......PAGE 6 • HARDWARE ILLUSTRATION....PAGE 7 • ASSEMBLY INSTRUCTIONS....PAGE 10 • EXPLODED VIEW........PAGE 17 • CONTACT PAGE........PAGE 18... -
Page 4: Safety Instructions
Powerline by Body Solid replacement parts when servicing this machine. Failure to do so will void your • Do no overexert yourself or work to exhaustion. warranty and could result in personal injury. • If you feel any pain or abnormal symptoms, stop your workout immediately and consult your physician. • Never operate unit when it has been dropped or For information about product operation or service, check out the official Powerline website damaged. Return the equipment to a service center for examination and repair. at www.bodysolid.com or contact an authorized • Never drop or insert objects into any opening in the Powerline dealer or a Powerline factory-authorized service company or contact Body-Solid customer equipment. service at one of the following: • Always check the unit and its cables before each use. Make sure that all fasteners and cables are secure Toll Free: 1-800-556-3113 and in good working condition. Phone: 1-708-427-3555 • Do not use the equipment outdoors or near water. Fax: 1-708-427-3556 Personal Safety During Assembly Email: service@bodysolid.com • Before beginning assembly, please take the time to Or write to: Body-Solid, Inc. -
Page 5: Preparation
PLA1000 PREPARATION Required tools Assembly Tips The basic tools that you must obtain before assembling Read all “Notes” on each page before beginning each step. the PLA1000 include but are not limit to: While you may be able to assemble the PLA1000 using the • Standard Wrench Set illustrations only, important safety notes and other tips may be included in the text. • Metric Wrench Set Some pieces may have extra holes that you will not use. Use • Adjustable Wrench only those holes indicated in the instructions and illustrations. • Standard / Metric Allen Key Set NOTE: With so many assembled parts, proper alignment and adjustment is critical. While tightening the nuts and bolts, be sure to leave Installation Requirements room for adjustments. Follow these installation requirements when assembling the PLA1000: NOTE: The bottles that are marked “Poison” is your touch up paint. Keep away from children. Set up the PLA1000 on a solid, flat surface. A smooth, flat surface under the machine helps keep it level. CAUTION: Obtain assistance! If you feel like you can’t assemble the PLA1000 by yourself then do Provide ample space around the machine. Open space not attempt to do so as this could result in around the machine allows for easier access. injury. Review the Installation Requirements before proceeding with the following steps. For aesthetic purposes, insert all bolts in the same direction unless specified (in text or illustrations) to do otherwise. -
Page 6: Part/Hardware List
PLA1000 PART LIST Part # DESCRIPTION BASE CROSSMEMBER BASE FRAME CHROME UPRIGHT SLIDING CARRIAGE TOP FRAME LAT BAR LOW ROW BAR STEEL BRACKET PULLEY BRACKET M12x80mm HEX HEAD BOLT M10x65mm HEX HEAD BOLT M10x45mm HEX HEAD BOLT M10 LOCK WASHER M12 WASHER M10 WASHER M12 NYLON LOCKNUT... -
Page 7: Hardware Illustration
PLA1000 HARDWARE ILLUSTRATION Part #1 M12x80mm hex head bolt QTY . 12 Part #2 M10x65mm hex head bolt QTY. 1 Part #3 M10X45mm HEX HEAD BOLT QTY. 6 Part #4 M10 LOCK WASHER QTY.1... - Page 8 PLA1000 HARDWARE ILLUSTRATION Part #5 M12 WASHER QTY. 24 Part #6 M10 WASHER QTY . 15 Part #7 M12 NYLON LOCK NUT QTY. 12 ...
- Page 9 PLA1000 NOTE...
-
Page 10: Assembly Instructions
PLA1000 STEP 1 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: finger tighten all hardware FIRST. wrench tighten all hardware at the END of step 1F. some components may be pre-assembled. attach Base Frame (B) to Base Crossmember (A) using: 2 - (#1) m12x80mm hex head bolt 4 - (#5) m12 flat washer 2 - (#7) m12 nylon lock nut... - Page 11 PLA1000 STEP 1 above shows step 1 assembled and completed...
- Page 12 PLA1000 STEP 2 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: finger tighten all hardware FIRST. wrench tighten all hardware at the END of step 2F. some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. 2A.
- Page 13 PLA1000 STEP 2 above shows step 2 assembled and completed...
- Page 14 PLA1000 STEP 3 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. 3A. Attach Lat Bar (F) to Top Cable (#17). 3B.
- Page 15 PLA1000 STEP 3 above shows step 3 assembled and completed...
- Page 16 PLA1000 NOTE...
-
Page 17: Exploded View
PLA1000 PLA1000 EXPLODED VIEW EXPLODED VIEW... -
Page 18: Contact Page
PLA1000 please write your serial number in the boxes below 014749-��-��-����-���� S/N # 1900 S. Des Plaines Ave. Forest Park, IL 60130 Phone:(708)427-3555 Fax:(708)427-3556 Hours: M-F 8:30 - 5:00 CST...