Page 2
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout. Check that all nuts, bolts, screws and pop pins are in place and fully tightened. Also, before use, check cables for sign of wear. Replace all worn parts immediately.
Keep hands, limbs, loose clothing, and long hair well description from this Owner’s Manual. Use only out of the way of all moving parts Powerline by Body Solid replacement parts when • Use care when getting on or off the unit.
PPA-13X PREPARATION Required tools Assembly Tips The basic tools that you must obtain before assembling Read all “Notes” on each page before beginning each step. the PPA-13X include but are not limit to: While you may be able to assemble the PPA-13X using the •...
PPA-13X HARDWARE ILLUSTRATION Part #1 M10X70mm hex head bolt Qty. 4 Part #2 M10X50mm hex head bolt Qty. 2 Part #3 M10X40mm hex head bolt Qty. 2 Part #4 M8X65mm hex head bolt Qty. 2 Part #5 M10X16mm hex head bolt Qty.
Page 8
PPA-13X HARDWARE ILLUSTRATION CONT. Part #7 M8 washer Qty. 2 Part #8 M10 washer Qty. 4 Part #9 M8 spring washer Qty. 2 Part #10 foam roller Qty. 2 Part #11 2”X2” plastic cover Qty. 1 Part #13 2”X2” end cap Qty.
PPA-13X PART LIST Part A Part B Part C center arm frame pulley plate right arm frame [1pcs] [1pcs] [1pcs] Part D Part E Part F left arm frame pulley frame pulley holder [1pcs] [1pcs] [1pcs] Part G support pad [1pcs]...
PPA-13X STEP 1 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: finger tighten all hardware in this step. DO NOT wrench tighten until the last step. some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. 1A.
Page 11
PPA-13X STEP 1 left shows STEP 1 assembled and completed main upright of PLA-144X...
Page 12
PPA-13X STEP 2 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: finger tighten all hardware in this step. DO NOT wrench tighten until the last step. some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. NOTE: left, right, top, and bottom are referenced as if you were in the position of using the machine.
Page 13
PPA-13X STEP 2 Left shows STEP 2 assembled and completed...
Page 14
PPA-13X STEP 3 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: finger tighten all hardware in this step. DO NOT wrench tighten until the last step. some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. NOTE: this step is intended to show you where each pulley gets assembled and what hardware you need to use.
Page 15
PPA-13X STEP 3 Left shows STEP 3 assembled and completed...
Page 16
PPA-13X STEP 4 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: finger tighten all hardware in this step. DO NOT wrench tighten until the last step. some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. Cable routing: (P1) attach cable to round insert of left...
PPA-13X please write your serial number in the boxes below S/N # Body-Solid ® Built for Life 1900 S. Des Plaines Ave. 1900 S. Des Plaines Ave. Forest Park, IL 60130 Forest Park, IL 60130 Phone:(708)427-3555 Phone:(708)427-3555 Fax:(708)427-3556 Fax:(708)427-3556 Hours: M-F 8:30 - 5:00 CST Hours: M-F 8:30 - 5:00 CST www.bodysolid.com Copyright 2011.