PSM200 SAFETY INSTRUCTIONS The PSM200 is designed for your enjoyment. By When using exercise equipment, following these precautions and using common sense, you should always take basic you will have many safe and pleasurable hours of precautions including the healthful exercise with your Powerline Smith Machine. following: After assembly, you should check all functions to • Read all instructions before using the PSM200. These ensure correct operation. If you experience problems, instructions are written to ensure your safety and to protect the unit. first recheck the assembly instructions to locate any possible errors made during assembly. If you are • Do not remove any safety labels from the unable to correct the problem, call the dealer from machine. • Do not allow children on or near the equipment. whom you purchased the machine or call 1-800-556- 3113 for the dealer nearest you. • Use the equipment only for its intended purpose as described in this guide. Do not use accessory attachments that are not recommended by the Obtaining Service manufacturer. Such attachments might cause serious Please use this Owner’s Manual to make sure that...
PSM200 PREPARATION Required tools Assembly Tips The basic tools that you must obtain before assembling Read all “Notes” on each page before beginning each step. the PSM200 include but are not limit to: While you may be able to assemble the PSM200 using the • Standard Wrench Set illustrations only, important safety notes and other tips may be included in the text. • Metric Wrench Set Some pieces may have extra holes that you will not use. Use • Adjustable Wrench only those holes indicated in the instructions and illustrations. • Standard / Metric Allen Key Set NOTE: With so many assembled parts, proper alignment and adjustment is critical. While tightening the nuts and bolts, be sure to leave Installation Requirements room for adjustments. Follow these installation requirements when assembling the PSM200: NOTE: The bottles that are marked “Poison” is your touch up paint. Keep away from children. Set up the PSM200 on a solid, flat surface. A smooth, flat surface under the machine helps keep it level. CAUTION: Obtain assistance! If you feel like you can’t assemble the PSM200 by yourself then do Provide ample space around the machine. Open space not attempt to do so as this could result in around the machine allows for easier access. injury. Review the Installation Requirements before proceeding with the following steps. For aesthetic purposes, insert all bolts in the same direction unless specified (in text or illustrations) to do otherwise.
PSM200 PART LIST Part # DESCRIPTION LEFT BASE FRAME RIGHT BASE FRAME FRONT UPRIGHT CHROME GUIDE ROD REAR UPRIGHT TOP FRAME REAR BASE FRAME WEIGHT BAR STEEL BRACKET RIGHT SAFETY CATCH LEFT SAFETY CATCH LEFT J CUP RIGHT J CUP WEIGHT HORN HEX HEAD BOLT, M10x75mm FLAT HEAD CAP SCREW, M8x15mm...
PSM200 STEP 1 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: Finger tighten all hardware in this step. DO NOT wrench tighten until the last step. some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 10
PSM200 STEP 2 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: Finger tighten all hardware in this step. DO NOT wrench tighten until the last step. some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten.
Page 12
PSM200 STEP 3 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: Wrench tighten all hardware at the end of Step 3B. some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts, must wrench tighten. 3A.
Page 14
PSM200 STEP 4 BE CAREFUL TO ASSEMBLE ALL COMPONENTS IN THE SEQUENCE THAT THEY ARE PRESENTED. NOTE: Some components may be pre-assembled. nylon lock nuts will not fully screw onto bolts, must wrench tighten. Adjustable J Cups & Safety Catches Attach Left and Right J Cups (M &...
Page 15
PSM200 STEP 4 Above shows step 4 assembled IMPORTANT NOTE: and completed To make sure Weight Bar (H) sliding up and down properly, please lubricate the Chrome Guide Rods (D)
PSM200 please write your serial number in the boxes below 017924-��-��-����-���� S/N # 1900 S. Des Plaines Ave. Forest Park, IL 60130 Phone:(708)427-3555 Fax:(708)427-3556 Hours: M-F 8:30 - 5:00 CST...