Siemens S5-135U/155U System Manual page 556

Index
Removing and inserting
CPU 922 , 5-73
CPU 928 -3UA21, 5-56
CPU 928 , 5-64
CPU 928B, 5-45
CPU 928B -3UB21, 5-33
CPU 948, 5-19
CPU 948 -3UA13, 5-4
CPU 948 -3UA23, 5-4
modules, 8-18, 9-13, 9-42, 9-59, 9-84, 9-105
monitoring module, 10-6
Replacing the battery
power supply units, 4-41
PSU 6ES5 955-3NA12, 4-66
RESET
automatic, 6-13
CPU 948, 5-21
Reset
CPU 922, 5-75, 5-78
CPU 928, 5-69
CPU 928 , 5-66
CPU 928 -3UA21, 5-58, 5-60
CPU 928B, 5-48
CPU 928B -3UB21, 5-36, 5-39, 5-51
CPU 948 -3UA13, 5-7, 5-11
CPU 948 -3UA23, 5-7, 5-11
Resistance thermometers, connection, 9-20
Restart, 5-51
automatic, 6-13
CPU 922, 5-75, 5-78
CPU 928, 5-69
CPU 928 , 5-66
CPU 928B, 5-48
CPU 928 -3UA21, 5-58
CPU 928B -3UB21, 5-36, 5-39
CPU 948, 5-21, 5-25
CPU 948 -3UA13, 5-7, 5-12
CPU 948 -3UA23, 5-7, 5-12
Routing of lines, 3-5
RS422 A/485 submodule, 5-112
Rules for ensuring EMC, 3-5
S
S5 bus, 6-16
Selective sampling, 9-9, 9-54
Semaphores, 6-16, 6-20
Sensors, connection, 9-48, 9-89
Serial interface, 6-21
selection method, 6-22
Index-6
Shielding, 3-14
distributed arrangement of monitor and PLC,
3-30
Shielding of cables/lines, 3-14
Short-circuit protection, 8-24
Signal lines, connection, 8-21, 9-16, 9-45, 9-62,
9-87, 9-108
Signal output, 8-3
Signaling circuits
fan submodule, 4-72
of the power supply units, 4-26
Signaling function, power supply units, 4-20
SINEC H1 LAN, routing of cables, 3-11
SINEC L1 LAN, routing of cables, 3-11
SINEC L1 submodule, 5-118
SINEC L2 LAN, routing of cables, 3-11
Slot, 6-22
setting the number of CPU slots, 6-6
Slots, slots required by CPU, 1-1, 6-2
Standard connecting cables
PG submodule, 5-98
RS422 A/485 submodule, 5-117
TTY submodule, 5-109
V.24 submodule, 5-102
Start, 6-13
manual, 6-13
Start address, 8-15
Start address, subaddress, analog input/output
modules, 9-10, 9-40, 9-56, 9-103
Startup
CPU 922, 5-78
CPU 928 , 5-69
CPU 928 -3UA21, 5-60
CPU 928B, 5-39, 5-51
CPU 948, 5-25
CPU 948 -3UA13, 5-11
CPU 948 -3UA23, 5-11
Startup of CC, brief instructions, 4-10
Startup of the programmable controller, 4-10
Station number, 6-22
Status indicators
CPU 922, 5-76
CPU 928 , 5-67
CPU 928B, 5-49
CPU 928 -3UA21, 5-58
CPU 928B -3UB21, 5-37
CPU 948, 5-22
CPU 948 -3UA13, 5-8
CPU 948 -3UA23, 5-8
Stop state, 6-13
C79000-G8576-C199-06
System Manual