Table Of Contents - Kemppi Protig 410 Operation Instructions Manual

CONTENTS
1. PREFACE ........................................................................................................................ 3
1.1. Introduction ....................................................................................................................... 3
1.2. Product introduction .......................................................................................................... 3
1.2.1.
1.2.2.
1.3. Operation safety ................................................................................................................ 7
2. INSTALLATION ............................................................................................................... 7
2.1. Assembly of TIG/MMA equipment ..................................................................................... 7
2.1.1.
2.1.2.
2.1.3.
2.1.4.
2.1.5.
2.1.6.
2.1.7.
2.1.8.
2.1.9.
2.2. Installation of TIG/MMA equipment ................................................................................... 9
2.2.1.
2.3. Shielding gas ..................................................................................................................... 9
2.3.1.
2.4. Main switch I/O ................................................................................................................ 10
2.5. Operation of cooling unit (Procool 10, 30) ....................................................................... 10
3. OPERATION OF PANELS ............................................................................................ 11
3.1. Control panel TL 6271265 ............................................................................................... 11
3.1.1.
3.1.2.
3.1.3.
3.1.4.
3.1.5.
3.1.6.
3.1.7.
3.1.8.
3.1.9.
3.1.10.
3.1.11.
3.1.12.
3.2. Control panel TX 6271266 .............................................................................................. 14
3.2.1.
3.2.2.
3.2.3.
3.2.4.
3.2.5.
3.2.6.
3.2.7.
3.2.8.
3.2.9.
3.2.10.
4. ACCURACY OF PANEL DISPLAY ............................................................................... 18
5. REMOTE CONTROL UNIT ........................................................................................... 19
6. MAINTENANCE ............................................................................................................ 19
6.1. Welding torch .................................................................................................................. 19
6.2. Cables ............................................................................................................................. 20
7. OPERATION DISTURBANCES .................................................................................... 20
8. DISPOSAL OF THE MACHINE ..................................................................................... 20
9. ORDERING NUMBERS ................................................................................................ 21
10. TECHNICAL DATA ........................................................................................................ 22
11. TERMS OF GUARANTEE ............................................................................................. 23
2 - PROTIG 410 / 0537
Operation control and connectors ................................................................................... 3
Accessories and cables .................................................................................................. 5
Installation of power source ............................................................................................ 7
Assembly of transport wagon and mounting of Pro power source to wagon .................. 7
Mounting of Protig 410 unit onto the power source ......................................................... 7
Mounting of Protig 410 control panel .............................................................................. 8
Connecting cables ........................................................................................................... 8
Connecting torch and extension cable ............................................................................ 8
Use as terminal unit ........................................................................................................ 8
Assembly and controls of MIG/TIG/MMA equipment ...................................................... 8
Remote control units ....................................................................................................... 9
Choice of electrode and flow amount of shielding gas .................................................... 9
Installing gas bottle ......................................................................................................... 9
Selection of MMA/TIG welding ...................................................................................... 11
Selection of TIG ignition method ................................................................................... 11
Selection of torch switch operation ............................................................................... 12
Adjustment of control unit .............................................................................................. 12
Parallel control unit for welding current ......................................................................... 13
Pre-gas time display and current up-slope time display ................................................ 13
Display of current down-slope time ............................................................................... 13
Display of post gas time ................................................................................................ 13
Display of welding current ............................................................................................. 13
Local and remote control of welding current ................................................................. 13
Controls for TIG welding ............................................................................................... 13
Controls for MMA welding ............................................................................................. 14
Control ranges for time and per cent ............................................................................. 15
Demo: Learning and control state ................................................................................. 15
Controls for continuous welding .................................................................................... 16
Controls for pulsed TIG welding .................................................................................... 16
Controls for fusion spot welding .................................................................................... 17
MINILOG-operation and control for start current ........................................................... 17
Breaking down-slope operations ................................................................................... 17
Program storing of Selectotig ........................................................................................ 18
Programming of numeric channels ............................................................................... 18
Programming of dot channels ....................................................................................... 18
© KEMPPI OY