Cisco ASR 9000 Series Configuration Manual page 78

ROM Monitor Upgrade: Example
% RELOAD REMINDER:
- The upgrade operation of the target module will not interrupt its normal
operation. However, for the changes to take effect, the target module
will need to be manually reloaded after the upgrade operation. This can
be accomplished with the use of "hw-module <target> reload" command.
- If automatic reload operation is desired after the upgrade, please use
the "reload" option at the end of the upgrade command.
- The output of "show hw-module fpd location" command will not display
correct version information after the upgrade if the target module is
not reloaded.
Continue? [confirm]
Starting the upgrade/download of following FPD:
=========== ==== ======= ======= =========== =========
Location
=========== ==== ======= ======= =========== =========
0/RSP1/CPU0 lc
------------------------------------------------------
RP/0/RSP1/CPU0:Nov 19 07:24:11.553 : lc_fpd_upgrade[243]: %PLATFORM-UPGRADE_FPD-6-START :
Starting to upgrade rommon subtype image from 0.63 to 0.64 for this card on location
0/RSP1/CPU0
RP/0/RSP1/CPU0:Nov 19 07:24:11.561 : rommon_fpd_agent[308]: Start Upgrade...
RP/0/RSP1/CPU0:Nov 19 07:24:11.561 : rommon_fpd_agent[308]: Programming fpd instance 0...with
file
/net/node0_RSP0_CPU0/dev/shmem/asr9k-fpd-3.7.2.10I/fpd/ucode/rommon-viking-8641d-rsp2-B.bin
RP/0/RSP1/CPU0:Nov 19 07:24:21.098 : lc_fpd_upgrade[243]: %PLATFORM-UPGRADE_FPD-6-PASSED :
Successfully upgrade rommon subtype image for this card on location 0/RSP1/CPU0
% Successfully upgraded 1 FPD for A9K-RSP-4G-HDD on location 0/RSP1/CPU0
The following example shows reload of the 0/RSP1/CPU0 node:
RP/0/RSP0/CPU0:router(admin)#
WARNING: This will take the requested node out of service.
Do you wish to continue?[confirm(y/n)]
RP/0/RSP0/CPU0:Nov 19 07:26:45.060 : shelfmgr[323]: %PLATFORM-SHELFMGR-6-USER_RESET : Node
0/RSP1/CPU0 is reset due to user reload request
RP/0/RSP0/CPU0:Nov 19 07:26:51.866 : shelfmgr[323]: %PLATFORM-SHELFMGR-6-NODE_STATE_CHANGE
: 0/RSP1/CPU0 card type:1049346 nstate:ROMMON
RP/0/RSP0/CPU0:Nov 19 07:27:11.153 : shelfmgr[323]: %PLATFORM-SHELFMGR_HAL-6-BOOT_REQ_RECEIVED
: Boot Request from 0/RSP1/CPU0, Rommon Version: 0.64
RP/0/RSP0/CPU0:Nov 19 07:27:11.155 : shelfmgr[323]: %PLATFORM-SHELFMGR-6-NODE_STATE_CHANGE
: 0/RSP1/CPU0 card type:1049346 nstate:MBI-BOOTING
RP/0/RSP0/CPU0:Nov 19 07:29:26.661 : shelfmgr[323]: %PLATFORM-SHELFMGR-6-NODE_STATE_CHANGE
: 0/RSP1/CPU0 card type:1049346 nstate:IOS XR RUN
RP/0/RSP0/CPU0:Nov 19 07:29:52.066 : redcon[303]: %HA-REDCON-1-STANDBY_READY : standby card
is ready
Verify the upgrade using the show hw-module fpd location all command, as shown in the following command:
RP/0/RSP0/CPU0:router(admin)#
===================================== ==========================================
Location
============ ======================== ======= ==== ======= ==== =========== ====
0/RSP0/CPU0
--------------------------------------------------------------------------------
0/RSP0/CPU0
--------------------------------------------------------------------------------
Cisco ASR 9000 Series Aggregation Services Router ROM Monitor Configuration Guide, Release 5.1.x
70
Current
Type Subtype Upg/Dng Version
rommon upg
hw-module location 0/RSP1/CPU0 reload
show hw-module fpd location all
Card Type
A9K-RSP-4G
ASR-9010-FAN
Upgrading and Downgrading ROM Monitor Firmware
Upg/Dng
Version
0.63 0.64
y
Existing Field Programmable Devices
==========================================
HW
Version Type Subtype Inst
4.8 lc fpga3 0
lc fpga1 0
lc fpga2 0
lc cbc 0
lc fpga4 0
lc hsbi 0
lc rommon 0
1.0 lc cbc 1
Current SW Upg/
Version Dng?
1.18 No
1.05 No
1.15 No
1.02 No
3.08 No
4.00 No
1.04 No
4.00 No
OL-30420-01