Mitsubishi Electric RD81MES96 User Manual page 19

No. Name
(2) Dot matrix LED
(3) Slot cover
(4) SPEED LED(CH1, CH2)
(5) SD/RD LED(CH1, CH2)
*1
(6) Ethernet port (CH1, CH2)
(7) Dot matrix LED display mode switch
(SELECT/MODE/SHOW switch)
(8) SD memory card lock switch
(SD CARD OFF button)
(9) SD memory card slot
(10) Product information marking
*1 Only CH1 can be connected to MES Interface Function Configuration Tool with direct connection.
Dot matrix LED display
The following table shows the contents of the display mode displayed on the dot matrix LED when switching the display mode
to "SHOW".
Display mode name
USR
ENo.
IP1
IP2
BUF1
BUF2
The following display switching of dot matrix LED can be set by using MES Interface Function Configuration
Tool.
• Default display mode at power ON (Initial value: USR)
• The display mode is switched to ENo. (error code) forcibly when an error occurs.
• ENo. (error code) is highlighted.
Description
Displays the contents of each display mode or the results of the self-diagnostic test.
The following contents are displayed in each display mode.
• User specification character: Scrolled and displayed by the width of approximately 3 characters (3.3
characters).
• Error code: Displayed in four digits in hexadecimal (When multiple errors occur, only the latest error code is
displayed.)
• IP address: Scrolled and displayed by 4 characters in decimal.
• DB buffer use rate: Displayed in three digits in decimal + %.
For the display when performing the self-diagnostic test, refer to the following manual.
MELSEC iQ-R MES Interface Module User's Manual (Application)
A cover of the SD memory card slot and the switches.
Open this cover to insert/remove an SD memory card or to operate the switches.
Close the cover unless inserting/removing an SD memory card or operating the switches to prevent foreign
material intrusion such as dust.
Indicates the communication speed and the link status for Ethernet.
• ON (orange): Linking-up (1000 Mbps)
• ON (green): Linking-up (100 Mbps)
• OFF: Linking-down or linking-up (10 Mbps)
Indicates the data sending/receiving status for Ethernet.
• ON: Sending/receiving data
• OFF: Not send/receive data
A port for connecting to an Ethernet device
(IEEE802.3, 1000BASE-T/100BASE-TX/10BASE-T standards-compliant)
A switch for switching the display of dot matrix LED.
• MODE: Displays the display mode name that is currently selected.
• SELECT: Selects (switches) the display mode
Order: USR → ENo. → IP1 → IP2 → BUF1 → BUF2 → USR
• SHOW: Displays the contents of the selected display mode (Page 17 Dot matrix LED display)
Keep this display mode switch in the SHOW state during operation, and operate the switch only when
switching the display mode.
A switch for disabling access to an SD memory card to remove it.
Removing an SD memory card is prohibited while the CARD RDY LED is ON or flashing.
For the procedure to insert/remove SD memory cards, refer to the following section.
Page 58 Inserting and removing method of SD memory cards
A slot to insert an SD memory card
(SD, SDHC standards-compliant: 2 GB (SD) to 16 GB (SDHC))
Displays the product information (16 digits) of the module.
Description
Displays the characters specified in the action.
Substitute characters to display on the S_MATRIXLED_DISP (dot matrix LED display) of the system variable in the
action. For details on the action, refer to the following manual.
MELSEC iQ-R MES Interface Module User's Manual (Application)
Displays the error code.
Displays the IP address of the Ethernet port CH1.
Displays the IP address of the Ethernet port CH2.
Displays the use rate of the DB buffer 1.
Displays the use rate of the DB buffer 2.
1
1 PART NAMES
17