Table of Contents
Advertisement
FXS Port #2: SIP UserID and Authenticate ID left blank, Hunting Group set to "1"
FXS Port #3: SIP UserID and Authenticate ID left blank, Hunting Group set to "1"
FXS Port #4: SIP UserID and Authenticate ID entered, Hunting group set to "Active"
FXS Port #5: SIP UserID and Authenticate ID left blank, Hunting Group set to "4"
FXS Port #6: SIP UserID and Authenticate ID left blank, Hunting Group set to "4"
FXS Port #7: SIP UserID and Authenticate ID entered, Hunting group set to "Active"
FXS Port #8: SIP UserID and Authenticate ID left blank, Hunting Group set to "7"
...
FXS Port #24: SIP UserID and Authenticate ID left blank, Hunting Group set to "2"
Hunting Group 1 contains ports 1, 2, 3. Hunting Group 4 contains ports 4, 5, 6.
Hunting Group 7 contains ports 7, 8.
Please be aware, the choice of 1 for ports 2 and 3, the choice of 4 for ports 5 and 6, the choice 7 for port
8 is req uired to indicate that the SIP
account tied to port marked as
"Active" will be used for all
members of the same Hunting group. Needless to say, those members of the same Hunting group may
not be sequential ports. In following example ports 3, 5 and 7 tied to SIP Account configu red in Port #1
marked as "Active", and ports 4,6,8 tied to SIP Ac count configured in Port #2 marked as "Active" as
well.
Example of not sequential configuration of a multiple Hunting Group:
FXS Port #1: SIP UserID and Authenticate ID entered, Hunting group set to "Active"
FXS Port #2: SIP UserID and Authenticate ID entered, Hunting Group set to "Active"
FXS Port #3: SIP UserID and Authenticate ID left blank, Hunting Group set to "1"
FXS Port #4: SIP UserID and Authenticate ID left blank, Hunting group set to "2"
FXS Port #5: SIP UserID and Authenticate ID left blank, Hunting Group set to "1"
FXS Port #6: SIP UserID and Authenticate ID left blank, Hunting Group set to "2"
FXS Port #7: SIP UserID and Authenticate ID left blank, Hunting group set to "1"
FXS Port #8: SIP UserID and Authenticate ID left blank, Hunting Group set to "2"
...
FXS Port #24: SIP UserID and Authenticate ID left blank, Hunting Group set to "2"
Note: A single call directed to the SIP account will NOT resu lt in all ports ringi ng at the same time. They
will ring in the hunting group only. This feature is applicable to incoming calls only.
There are two types of hunting grou ps, Linear and Circular. Linear style will sort the call to the lowest-
numbered available line, this is also called "serial hunting". Circular style will distribute the calls "round-
robin". If a call is assigned to line 1, the next call goes to 2 and the next to 3. T he succession throughout
each of the lines continues even if one of the previous lines becomes available. When the end of the hunt
group is rea ched, the hunt ing starts over at the firs t line. Lines a re skipped if they are still busy on a
previous call. These two hunting styles can be configured from the Profile_x page.
I
-
C
NTER
PORT
ALLING
In some cases a user may want to make phone calls between the phones connected to multiple ports of
the same gateway when it is used as a stand alone unit, without the use of a SIP server. This feature will
also be applicable when the gateway is used with Hunting Groups and is reg istered to SIP serve r only
with one master number. In such cases users still wi ll be able to make inte r-port calls by using the IVR
feature.
Grandstream Networks, Inc.
Page 16 of 40
GXW40XX User Manual
Firmware 1.0.5.10
Last Updated: 01/2012
Advertisement
Table of Contents
