1. Manuals
  2. Brands
  3. Wenger Manuals
  4. Indoor Furnishing
  5. Diva
  6. Owner's manual

Wenger Diva Owner's Manual

Acoustical shell
Hide thumbs Also See for Diva:
Table of Contents

Advertisement

Quick Links

Download this manual
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .3
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Diva Acoustical Shell Set Up . . . . . . . . . . . . . . . . . . . . . . . . .4
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Ceiling Panel Performance Angles . . . . . . . . . . . . . . . .5
Ceiling Panel Storage Position . . . . . . . . . . . . . . . . . . .6
Tower Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Moving Towers from Storage . . . . . . . . . . . . . . . . . . . . .9
Tower Performance Position Setup . . . . . . . . . . . . . . . .13
Tower Wing Panel Doors . . . . . . . . . . . . . . . . . . . . . . . .15
Ceiling Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Ceiling Light Electrical Schematic . . . . . . . . . . . . . . . . .16
Ceiling Light Electrical Connection . . . . . . . . . . . . . . . .16
note: Please read and understand this Owner's Manual before working with or using the Diva
Acoustical Shell.
note: Refer to the illustrations on the following pages. If you need additional information,
contact the Wenger Corporation using the information below.
©Wenger Corporation 2012
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com
Diva
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Towers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Ceiling Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Ceiling Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Tower Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Diagonal Brace Assembly . . . . . . . . . . . . . . . . . . . . . . .18
Base Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Vertical Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . .20
Lower Filler Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Slide Lock Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Wing Stay Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Tower Trim Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Ceiling Panel Replacement Parts . . . . . . . . . . . . . . . . .26
Ceiling Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Ceiling Panel Stay Assembly . . . . . . . . . . . . . . . . . . . . .27
Bowstring Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Hanger Arm Assembly . . . . . . . . . . . . . . . . . . . . . . . . . .29
Truss Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Ceiling Panel Catch Assembly . . . . . . . . . . . . . . . . . . .31
Ceiling Panel Light Assembly . . . . . . . . . . . . . . . . . . . .32
Printed in USA 03/12
Owner's Manual
acoustical shell
®
. . . . . . . . . . . . . . . . . .21
®
Part #185C750-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Diva and is the answer not in the manual?

Questions and answers

Related Manuals for Wenger Diva

Summary of Contents for Wenger Diva

  • Page 1: Table Of Contents

    Base Frame ........19 Diva Acoustical Shell Set Up ......4 Vertical Frame Assembly .

  • Page 2: Safety

    WaRning WaRning WaRning Make sure that anyone Failure to comply with Always observe and comply working with the Diva Warnings and Cautions in with the Warnings and Acoustical Shell has read this document can result in Cautions posted on the...

  • Page 3: Important User Information

    Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in this manual. In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this manual.

  • Page 4: Diva Acoustical Shell Set Up

    The number of Towers and Ceiling Panels used, how they overlap, and the performance angles can be adjusted for different effects. Some Towers have one or two doors for easy stage access. Refer to the Wenger drawings for the initial set up. Diva...

  • Page 5: Ceiling Panel Performance Angles

    Ceiling Panel Rows are rotated into the vertical position and stored in the loft area. • The sequence for setting up the Diva Acoustical Shell is as follows. 1. Lower the Ceiling Panels first. a. Place the Ceiling Panels in a position where the Panels can be rotated from the Storage Position to the Performance Position, then, lift the Ceiling Panel Rows high enough to move Towers across the stage.

  • Page 6: Ceiling Panel Storage Position

    CoustiCal hell Continued eIlIng anel torage osItIon Ceiling Panels are either stored in a vertical position or are placed into the Performance Position. Refer to the illustrations below. Performance Position — the Ceiling Panel Row is rotated until the Ceiling Stay Receiver •...

  • Page 7: Placing Ceiling Panels Into Performance Position

    CoustiCal hell Continued laCIng eIlIng anels erformanCe osItIon WaRning Always clear people and objects from the stage when moving Ceiling Panels to or from storage. To move a Ceiling Panel Row into the Performance Position, work from the Downstage side to the Upstage side.

  • Page 8: Changing The Ceiling Panel Performance Angle

    CoustiCal hell Continued hangIng the eIlIng anel erformanCe ngle WaRning Always clear people and objects from the stage when moving Ceiling Panels to or from storage. 1. Clear the stage of all people and objects that might interfere with lowering Ceiling Panels. Caution Do not allow a Ceiling Panel Row Upstage Edge to touch...

  • Page 9: Tower Set Up

    A separate Manual Wheeled Mover or Electric Air Transporter is required to lift and move Diva Towers. Caution Caution Never attempt to manually lift Never use the Wheeled Mover or Air Transporter for any or move a Diva Tower...
  • Page 10 Wheeled mover 3. Position the Wheeled Mover (shown) or Air Transporter under the Diva Tower with the Lifting Hooks under the Lifting Brackets on both sides of the Diva Tower. lifting bracket lifting hook...
  • Page 11 Panels to the storage position before moving the Tower to or from the performance position. 7. With one person pushing the Diva Tower and a second person guiding, slowly move (no faster than one-foot-per-second) the Tower to the performance position.
  • Page 12 oWeR Continued oVIng oWers torage ContInueD 8. When the Tower is in the final location, grip the handle of the Wheeled Mover firmly and slowly move it from the lower hook to the upper hook. If using an Air Transporter, turn off the power switch. The Tower will tilt slightly forward until it rests on the floor.

  • Page 13: Tower Performance Position Setup

    oWeR Continued oWer erformanCe osItIon etuP 1. Position the Tower Wing Panels. a. Turn the Wing Stay Lock about one-half turn counterclockwise to release the Wing Panel. b. Rotate the Wing Panel to the Performance Position. c. Lock the Wing Panel by turning the Wing Stay Lock clockwise until snug.
  • Page 14 oWeR Continued oWer erformanCe osItIon etuP ContInueD 3. Install the Lower Center Filler Panel to the Tower. a. Lift the Lower Center Filler Panel away from the back side of the Lower Center Panel. lower Center Panel lower Center filler Panel b.

  • Page 15: Tower Wing Panel Doors

    oWeR Continued oWer anel oors Wing Panels with a Door open as follows. note: When two Doors are adjacent, always open the the Door without Edge Trim first. 1. Turn the Slide Lock Knob counterclockwise to release the Slide Lock Slide. 2.

  • Page 16: Ceiling Panel Lights

    Ceiling Panel Lights Light electrical circuits Ceiling Panel electrical and other accessories must without consulting the components only with always be designed by an Wenger Corporation. components with the same electrical engineer and specification. comply with electrical codes and user requirements. Caution...

  • Page 17: Maintenance

    3. Replace any damaged part immediately. 4. Lubricate any Leveler parts that do not move freely with a general purpose grease. 5. Immediately replace any missing counterweights with Wenger Corporation replacement parts. 6. Be sure that all hinges move freely.

  • Page 18: Tower Replacement Parts

    oWeR ePlaCement aRts Iagonal raCe ssembly Item Description Item Description Hex Jam Nut, 1-8 Diagonal Cover Treaded Steel Bar, 1-8 x 44’...

  • Page 19: Base Frame

    oWeR ePlaCement aRts Continued rame Item Description Item Description Leveler Assembly Button Head Socket Screw, 3/8-16 x 1” Tower Base Weldment Hex Head Lock Nut, 3/8-16 Swiveling Caster, 6” DIA Self Tapping Screw, 1/4-20 x 1/2” Push Handle Carriage Bolt, 3/8-16 x 1” Weight Box Cover...

  • Page 20: Vertical Frame Assembly

    oWeR ePlaCement aRts Continued ertICal rame ssembly Item Description Item Description Right Hand Vertical Frame** Capscrew, 1/2-13 x 14” Left Hand Vertical Frame** Flange Bearing, .500 x .750 x .7500 Cross Brace Moving Hinge Lower Cross Brace Button Head Socket Screw, 3/8-16 x 7/8” Capscrew, 1/2-13 x 9”...

  • Page 21: Tower Wing-Door-Center Panel

    oWeR ePlaCement aRts Continued oWer enter anel Item Description Item Description Tower Panel** Polyethylene Extrusion Inner Corner Clip** Carriage Bolt, 1/4-20 x 3-1/2” Outer Corner Clip Hex Nut, 1/4-20 Self-Drilling Screw, 1/4-20 x 1” ** Specify length...

  • Page 22: Lower Filler Panel

    oWeR ePlaCement aRts Continued oWer Iller anel Item Description Item Description Lower Filler Panel Spring Pin, 5/16 x 1-3/4” Polyethylene Extrusion Pull Rod Door Handle Panel Latch Lever Inner Corner Clip Panel Latch Bracket Outer Corner Clip Hinge Rod Hex Head Self-Drilling Screw, 1/4-20 x 1” Blind Rivet, 3/16 x 3/8”...

  • Page 23: Slide Lock Assembly

    oWeR ePlaCement aRts Continued lIDe ssembly Item Description Item Description Slide Lock Housing Door Handle Slide Lock Knob Slide Lock Cushion Slide Lock Slide Philips Pan Head Screw, 1/4-20 x 5/8” Slide Lock Keeper...

  • Page 24: Wing Stay Assembly

    oWeR ePlaCement aRts Continued ssembly Item Description Item Description End Bracket Hex Head Capscrew, 3/8-16 x 3/4” Wing Stay Tube Hex Head Capscrew, 3/8-16 x 2-1/4” Wing Stay Channel Hex Head Capscrew, 3/8-16 x 1-5/8” Stay Base Bracket Wing Stay Lock Lock Nut, 3/8-16 Phillips Pan Head Screw, 10-24 x 5/8”...

  • Page 25: Tower Trim Kit

    oWeR ePlaCement aRts Continued oWer Item Description Item Description Panel Trim Strip (specify length) Wing Trim Strip Lower Center Panel Trim Strip, 63.375 Masking Strip Filler Panel Trim Strip, 34” Hex Head Self-Drilling Screw, 1/4-20 x 1”...

  • Page 26: Ceiling Panel Replacement Parts

    eiling anel ePlaCement aRts Continued eIlIng anel Item Description Item Description Ceiling Panel (specify size) Blind Rivet, 3/16 x 3/8” Ceiling Panel Channel (specify length) Carriage Bolt, 1/4-20 x 3-1/2” Outer Corner Clip Hex Nut, 1/4-20 Inner Corner Clip Polyethylene Extrusion Self-Drilling Screw, 1/4-20 x 1”...

  • Page 27: Ceiling Panel Stay Assembly

    eiling anel ePlaCement aRts Continued eIlIng anel ssembly Item Description Item Description Ceiling Panel Stay Tube and Bracket Lock Nut, 3/8-16 Compression Spring, .720” diameter Ceiling Stay Rod Lock Nut, 5/16-18 Hex Head Capscrew, 1/4-20 x 1-1/4” Bearing, 3/8” ID Latch Reciever Plate Latch Bar Lock Nut, 1/4-20...

  • Page 28: Bowstring Assembly

    eiling anel ePlaCement aRts Continued oWstrIng ssembly Item Description Item Description Bowstring (specify size and length) Bowstring Jack Jam Nut Ceiling Clip Self-Drilling Screw, 1/4-14 x 3/4” Bowstring Jack Lock Nut, 3/8-16 Bowstring Jack Tube Self-Tapping Screw, 5/16-18 x 1” Hanger Bracket Hex Head Screw, 3/8-16 x 2-1/4”...

  • Page 29: Hanger Arm Assembly

    eiling anel ePlaCement aRts Continued anger ssembly Item Description Item Description Hanger Arm Lock Nut, 3/8-16 Turnbuckle Hex Head Screw, 1/2-13 x 1-3/4, Grade 5 Hex Head Screw, 3/8-16 x 2”, Grade 5 Hanger Strap Hex Head Capscrew, 3/8-16 x 1” Grade 5 Lock Nut, 1/2-13 Batten Clamp Carriage Bolt, 1/2-13 x 3-3/4”...

  • Page 30: Truss Assembly

    eiling anel ePlaCement aRts Continued russ ssembly Item Description Item Description Ceiling Truss (specify length) Self Tapping Screw, 1/4-14 x 3/4” Ceiling Truss Cap (specify length) Splice Bar Ceiling Truss Splice...

  • Page 31: Ceiling Panel Catch Assembly

    eiling anel ePlaCement aRts Continued eIlIng anel atCh ssembly Item Description Item Description Pivot Plate Ceiling Catch Strap Catch Plate Hex Head Screw, 1/4-20 x 3” U-Bolt, 1/4-20 x 2” inside Lock Nut, 1/4-20 Spacer, Tube...

  • Page 32: Ceiling Panel Light Assembly

    eiling anel ePlaCement aRts Continued eIlIng anel Ight ssembly Item Description Item Description Flood Light Fixture, 575 watt Blind Rivet, 3/16 x 1/4” Lamp, 575 watt, 120VAC, 2000 Hour Truss Head Screw, 8-18 x 3/8” Light Mount Assembly Self-Drilling Screw, 1/4-20 x 1” Light Trim Ring Hex Head Screw, 1/2-13 x 1”...

Table of Contents