Danfoss VLT HVAC Drive FC 102 Operating Manual page 161

Operating Guide | VLT® HVAC Drive FC 102
FC 102
- Mains with contactor
2
[mm (AWG)]
2
- Motor [mm (AWG)]
Drive module power
loss at 600 V [W] (1) (2) (3)
Drive module power
loss at 690 V [W] (1) (2) (3)
Drive efficiency (2)
Output frequency [Hz] (4)
Heat sink overtempera-
ture trip [°C (°F)]
Control card overtem-
perature trip [°C (°F)]
PHF overtemperature
trip [°C (°F)]
dU/dt filter overtemper-
ature trip [°C (°F)]
Sine-wave filter over-
temperature trip [°C
(°F)]
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These values are based on a typical motor
efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimensioning of drive cooling. If the switching frequency is higher than the default
setting, the power losses can increase. LCP and typical control card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/
knowledge-center/energy-efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B
each add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficiency class, see the Ambient Conditions
section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses.
4
If using an output filter, the output frequency is limited further. See the Motor Output (U, V, W) section.
Table 78: Electrical Data, Mains Supply 3x525–690 V AC
FC 102
Normal overload
110% torque for a duration of 60 s.
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure size
Danfoss A/S © 2018.10
N110 N132 N160
2x95 2x95 2x95
(2x3/0 (2x3/0 (2x3/0
mcm) mcm) mcm)
2x95 2x95 2x95
(2x3/0 (2x3/0 (2x3/0
mcm) mcm) mcm)
1740 2101 2649
1798 2167 2740
0.98 0.98 0.98
0–590 0–590 0–590
110 (230) 110 (230) 110 (230)
80 (176) 80 (176) 80 (176)
150 (302) 150 (302) 150 (302)
150 (302) 150 (302) 150 (302)
150 (302) 150 (302) 150 (302)
N500
NO
400
500
500
E5h
N200 N250
2x185 2x185
(2x350 (2x350
mcm) mcm)
2x185 2x185
(2x350 (2x350
mcm) mcm)
3074 3723
3175 3851
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
150 (302) 150 (302)
150 (302) 150 (302)
150 (302) 150 (302)
N560 N630
NO NO
450 500
600 650
560 630
E5h E6h
Specifications
N315 N400
2x185 2x185
(2x350 (2x350
mcm) mcm)
2x185 2x185
(2x350 (2x350
mcm) mcm)
4465 5028
4614 5155
0.98 0.98
0–590 0–590
110 (230) 110 (230)
80 (176) 80 (176)
150 (302) 150 (302)
150 (302) 150 (302)
150 (302) 150 (302)
N710 N800
NO NO
560 670
750 950
710 800
E6h E6h
AQ262141314214en-000101 / 130R0880 | 161
N450
4x120
(4x250
mcm)
4x120
(4x250
mcm)
6062
5939
0.98
0–590
110 (230)
80 (176)
150 (302)
150 (302)
150 (302)