Laguna Tools Fusion F1 Owner's Manual
  1. Manuals
  2. Brands
  3. Laguna Tools Manuals
  4. Saw
  5. Fusion F1
  6. Owner's manual

Laguna Tools Fusion F1 Owner's Manual

Hide thumbs Also See for Fusion F1:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Fusion F1 Tablesaw
Owner's Manual
MTSF132110150-0130
Precision Tablesaw
7/31/2018
2072 Alton Parkway Irvine, CA 92606 U.S.A.
Service: +1 (949) 474-1200 or email customerservice@lagunatools.com
Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fusion F1 and is the answer not in the manual?

Questions and answers

Bill Medlen
April 5, 2025

The book says to loosen the bolts to square the table. What three bolts ?

0
1 comments:
Mr. Anderson
April 5, 2025

To square the table on the Laguna Tools Fusion F1, you need to loosen the two locking bolts and adjust the set screws as needed.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Laguna Tools Fusion F1

Summary of Contents for Laguna Tools Fusion F1

  • Page 1 Fusion F1 Tablesaw Owner's Manual MTSF132110150-0130 2072 Alton Parkway Irvine, CA 92606 U.S.A. Service: +1 (949) 474-1200 or email customerservice@lagunatools.com Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018 Precision Tablesaw 7/31/2018...

  • Page 2: Table Of Contents

    No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. Fusion F1 Tablesaw ©2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 7/31/2018...

  • Page 3: Safety

    "Freehand" means using your hands to support or guide the workpiece, in lieu of a rip fence or mitre gauge. Freehand sawing leads to misalignment, binding and kickback. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 4 Un protecteur mal fixé, endommagé ou ne fonctionnant pas correctement doit être réparé Use only 3-wire extension cords that have 3-prong grounding plugs and 3 pole receptacles that accept the ou remplacé. tool's plug. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 5 Stopper le fonctionnement de la scie et attendre l'arrêt de la scie avant de retirer le Nettoyer fréquemment et enlever la sciure accumulée sous la scie circulaire à table et/ou sous l'appareil matériau. de dépoussiérage. La sciure accumulée est combustible et peut s'enflammer. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 6 à table. Une installation incorrecte de la lame ou l'utilisation d'accessoires non recommandés peut entraîner de graves blessures. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 7: Warranty

    The owner's responsibility includes this warranty unless otherwise stated by Laguna Tools. These parts are designed to be used at the expense of the operator and are available for replacement or inventory purchase. The determination of a consumable part will but is not limited to the proper installation of the product in a safe environment, be made on a case-by-case basis by Laguna Tools.

  • Page 8: Reference

    Single Rail Cam Action Double Rail Cam Action 1.1.4 Dimensions Overall Size L39-3/4" W59-5/8" H38" L39-3/4" W65-5/8" H38" w/ 52" Extension +16" to W in Overall Size Base L19" W20" L18-5/8" W19-1/4" L19-3/4" W20-3/8" Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 9: Dimensions

    No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 10: Map

    Used without fence to perform cross cuts and angled cuts. Upper Trunnion Holds motor and blade. Trunnion Slides Allows for tilt mechanism. Guide Posts Allows for height change mechanism. Lower Trunnion Holds motor and blade. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 11: Control & Display Elements

    1.5 Accessories & Options The following accessories are designed for the Fusion Table-saws. These instructions should be followed exactly to properly set up the equipment. Some of these accessories are designed to fit multiple machines offered by Laguna Tools. Check the specification sheet for a fit guide of all REVO accessories.
  • Page 12 PT: 2.2 mm PT: 2.2 mm K: 3.6 mm K: 3.6 mm K: 3.2 mm K: 3.2 mm HK: 20 deg HK: 15 deg HK: 10 deg HK: 10 deg 60T, 5 deg 80T Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 13: Setup

    1. Do not cut deep into a box with a blade as it could scratch the paint; only cut deep enough to cut the tape or use a dull edge. 2. Prior to setting up the machine, organize all hardware and setup tools needed. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 14: Inventory

    Square Align Button Screw (for base) M8*1.25P*16 Flat Washer 8.5*16*2.0t T-Slot (square headed) Bolts M8*1.25P*20 Cap Screw M8*1.25P*20 Flat Washer 8.5*16*2.0t Anti-loose Nut M8*1.25P(13B*9H) Fig T003: Fusion Table-saw Inventory. Hex Screw w/Washer M8*1.25P*16/(13B*6.5H) Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 15: General Setup

    4. Install the fence holding brackets to the motor cover with shown hardware (104, should be easy for you to hit the emergency stop - the recommended position is at the joint of the two front rails. 5. Install motor cover to tablesaw. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 16 4. With the blade installed set the arbor height to the lowest position. 5. Install the new throat plate. 6. Lock the throat plate and adjust the set screws such that the throat plate has zero play and is solid with the table. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 17: Functional Setup

    There are three different safety devices included with the tablesaw. The completed blade guard assembly (3) offers the most protection and should be used whenever possible. Remove the blade guards and use the splitter/pawls (2) assembly only Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 18 3. Set the arbor tilt to 0 degrees and lock. 4. Raise saw to highest position. 5. Engage blade lock (2, red component). 6. Remove the arbor nut (3) and flange with (1) arbor wrench. 7. Remove or install blade. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 19: Maintenance

    3. Maintenance 3.1 Maintenance Work 3. Maintenance To keep you Laguna Tools machine in top performance for many years please WARNING! follow this maintenance schedule and refer to any instructions. WARNING! Never perform and setup, maintenance or adjustment procedures with the machine connected to the...

  • Page 20: Troubleshooting

    2. No suction 2. move motor cover and verify that the internal hose is fixed to the blade shroud port and the external 4" port. Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 21: A1. Wiring

    ALWAYS use the supplied wiring diagram with the machine or motor (under the electrical covering) if present. F3 (MTSF3362203-0130) NOTE: 220V(240V) Operation requires purchase of 220V magnetic switch (PTSF236110175-0130-124-1) Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

  • Page 22: A2. F1 Parts

    A2. F1 Parts WARNING! WARNING! Never perform and setup, maintenance or adjustment procedures with the machine connected to the power source! NOTICE! Only use authentic Laguna Tools parts for replacements. See Specifications here: 1.1 Specifications Customer Support: (949)-474-1200 or customerservice@lagunatools.com...
  • Page 23 Handwheel Handle See 93 for Assembly 920718-002 PTSF1-115 Cap Screw,Lock Washer M5*0.8P*12-5.1*9.3*1.3t 001801-102 PTSF1-117 Phillips Screw M4.5*1.81P*9 001103-901 PTSF1-118 Push Stick Holder 170965-904 PTSF1-119 Push Stick 230334-615 PTSF1-122 Flat Washer 8.4*15(BW-8) 006504-100 Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 24 *220v operation require purchase of additional switch - See key 1* in parts table. PTSF1-116 Hex. screw M6*1.0P*12 000002-101 PTSF1-120 Flat Washer 6.7*16*1.0t 006001-033 PTSF1-121 Square Nut M6*1.0P(10B*5H) 008603-100 PTSF1-122 Washer 8.4*15(BW-8) 006504-100 Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 25 031011-001 PTSF1-64 Hex. screw M6*1.0P*16 000002-103 PTSF1-65 Flat Washer 6.4*16*1.6t 006007-114 PTSF1-66 Lead Screw 361245-901 PTSF1-67 S ring STW-16 010007-000 PTSF1-68 Trunnion 090324-000 PTSF1-69 Bevel Gear 130257-000 PTSF1-70 Flat Washer 6.4*16*1.0t 006001-025 Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 26 Hex Nut M8*1.25P(13B*6.5H) 008006-100 14.14 PTSF1-14.14 Flat Washer 8.5*16*2t 006001-049 14.15 PTSF1-14.15 Plastic Set Screw M12*1.75P 250472-621 14.16 PTSF1-14.16 Hex. screw M10*1.5P*50 000004-306 14.17 PTSF1-14.17 Handle 230301-615 14.18 PTSF1-14.18 Compress Cam Assembly 922141-000 Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 27 M5*0.8P(8B*6H) 008302-100 PTSF1-2.7 Pan Head Screw M5*0.8P*6 000303-101 PTSF1-2.8 Bolt 230336-615 PTSF1-2.9 Rod Bracket -Left 130270-903 2.10 PTSF1-2.10 Rod Bracket -Right 130271-903 2.11 PTSF1-2.11 Pan Head Screw M4*0.7P*10 000302-103 2.12 PTSF1-2.12 360960-901 Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 28 8, 10 Dust Collection Guard Shipping Damage Dust Extraction Port Shipping Dimensions - M - Dust Port Outer Diameter Shipping Weight Maintenance Sliding Table Attachment Miter Gauge Standard Throat Plate Mitre Gauge Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...
  • Page 29 No part of this publication may be reproduced, transmitted, or translated into any language in any form by any means without our written permission. Errors and omissions may be current. Fusion F1 Tablesaw ©2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 7/31/2018...
  • Page 30 Lagunatools.com 2072 Alton Parkway Irvine, CA 92606 U.S.A. For Customer Service: +1 (949) 474-1200 or email customerservice@lagunatools.com Fusion F1 Tablesaw © 2018 Laguna Tools 7/31/2018...

Table of Contents