Summary of Contents for Laguna Tools DAKE Euromatic 370S
Page 1
DAKE SEMI-AUTOMATIC COLD SAW Euromatic 370S & 370S-L INSTRUCTIONAL MANUAL Read and understand all instructions and responsibilities before operating. Failure to follow safety instructions and labels could result in serious injury. Dake Corporation Phone: 800.937.3253 www.dakecorp.com 1809 Industrial Park Dr Grand Haven, MI 49417...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TABLE OF CONTENTS DAKE STANDARD LIMITED WARRANTY ............2 RETURN & REFUND POLICY ................4 SPECIFICATIONS ....................5 SAFETY ........................ 6 SET UP ......................... 8 TRANSPORTING AND INSTALLATION ............8 ELECTRICAL CONNECTION ..............
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com DAKE STANDARD LIMITED WARRANTY Finished Machines Dake warrants to the original purchaser the finished machine manufactured or distributed by it to be free from defects in material and workmanship under normal use and service within 1 year (12 months) from the delivery date to the end user.
Page 4
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Warranty Exceptions: The following conditions are not applicable to the standard limited warranty: (a) Part installation or machine service was not completed by a certified professional, and is not in accordance with applicable local codes, ordinances and good trade practices.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com RETURN & REFUND POLICY Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are here to help. Returns All Dake manufactured / distributed machines, parts and couplings include a 30-day return option.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SPECIFICATIONS Model Euromatic 370S Euromatic 350S-L 976200-2 976202-2 Number 220V/440V 220V/440V Voltage (440 with transformer) (440 with transformer) 3-Phase 3-Phase Phase Ferrous, Non-Ferrous, Non-Ferrous, Plastic Cutting Ability Plastic 3.5/4.5 HP 3.5/4.5 HP Horsepower 25/50 RPM...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SAFETY Carefully read all safety messages in these instructions and on your machine safety signs. Keep safety labels in good condition. Replace missing or damaged labels. Employer is responsible to perform a hazard/PPE assessment before work activity. Label Part No.
Page 8
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Additional Safety Warnings: • This machine is intended to be operated by one person. This person should be conscious of the machine movement not only for themselves but also for persons on the immediate area of the machine.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SET UP TRANSPORTING AND INSTALLATION 1. Remove box or shrink wrap. Carefully inspect the machine for any physical damage. 3. Check that all standard parts and optional accessories are included with machine. Some accessories may be located in chip drawer or behind the access door.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com AIR SUPPLY SET UP Locate the air regulator on the rear of the vertical column and connect the air supply. 1. Once all the air fittings are secure, turn the air supply on to the machine. The gauge should read 90 PSI.
Page 11
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Failure to remove backlash may result in blade breakage and serious injury. 9. While holding the blade against the pins tighten the spindle bolt securely. 10. Close blade cover and replace clear protective cover. Blade Installation for a Non-Ferrous Head: 1.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com CHOOSING A BLADE The saw will come with a “DAKE Saw Pitch Calculator” to assist in blade selection. First the pitch of the teeth must be chosen, suitable for the material to be cut, according to these criteria: •...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com For non-ferrous cutting head: Same rules apply as with the ferrous cutting head. The selection of tooth configurations is more limited with carbide. Solid material from 2”- 4”: 14” x 60 tooth blade is recommended. Solid material from 1”- 2”: 4”...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com SETTING HEAD PARAMETERS This is a dependable method of reducing “dead air” cutting. The picture above illustrated the four basic parts of the head positioning system. Lower limit adjustable cam block. Machined T-slot way that the cam moves vertically in.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 5. After stopping the head, loosen the upper head setting cam (the cam block on bottom), and raise the cam up to where it touches the limit switch without depressing the limit switch button.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com VISE ADJUSTMENTS Proper vise set up and adjustments are very important for quality and safe cutting. WARNING PROPERLY ADJUST ALL VISES BEFORE CUTTING. MAKE SIRE THE BLADE WILL NOT STRIKE ANY STEEL PARTS OF THE MACHINE. IF DEEP MITER CUTS ARE BEING MADE, LOWER WEAR PLATES MAY BEED TO BE REPLACED WITH ALUMINUM PLATES OR REMOVED AND A CLEARANCE CUT MADE INTO THE PLATES WITH A STEEL CUTTING SAW.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com • To maintain this cutting position adjustments to the rear vise will be necessary. • This adjustment is made by loosening the rear vise and sliding the T-slots forward or back to reach this optimal position.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TUBING FIXTURES EXAMPLES OPERATION Operating Tips: • Blade Tips o Always inspect blade before installing on machine, if questionable do not use. o Check gullets on blade. Check teeth and surfaces of blade. If a chip is packed in the gullets do not use, a blade in this condition will “thump”...
Page 19
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com o Keep your blades sharp. Do not keep cutting on a dull blade. This may damage the blade and your material as well as put stress on the machine. o Always have your blade sharpened by a qualified professional.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com CONTROLS A: Power Switch B: Cycle Start Button C: Head Feed Flow Control D: Security Key Switch E: Power On Indicator Light F: Motor Speed Switch G: E-Stop Button H: Air Pressure Gauge I: Security Interrupted Indicator Light STARTING THE SAW...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com 7. Use the head feed control knob to adjust the decent of the blade. When the blade finishes the cut and makes contact with the lower limit switch blade rotation will stop and the head will return to the upper position.
Page 22
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Daily Maintenance • Check and/or add oil to head feed cylinder as needed. • Empty chip drawer. • Add 2 pumps of oil to way oilers. Weekly Maintenance • Check and add coolant as needed. •...
Page 23
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com • Way Oiler: This reservoir is on the back of the column and needs to be kept full. At the beginning of each shift, this should be pumped twice to maintain good lubrication for the ways.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Blade pitch is incorrect, blade Replace blade, regrind, clean Blade chatter while cutting gullets are packed gullets Part not clamped properly, Re-clamp or fixture as Part moves while cutting rear vise needed...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com EXPLODED VIEWS AND PART LISTS Head Cylinder Unit: 976200-2, 976202-2 REV112019...
Page 28
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Head Cylinder Unit: Item Part Name Part No. Gasket Gasket 102* Cylinder Head Tank Head Plug Gasket – 2 pieces 11558 Transparent Pipe 300273 Tank Bottom Pipe Chromium Plated Rod Gasket Gasket Central Head...
Page 29
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Bedplate Unit: 976200-2, 976202-2 REV112019...
Page 30
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Bed Plate Unit: Item Part Name Part No. Head Piston Screw Washer Column Screw Left Guide Bushing Right Guide Limit Switch 300211 Screw Screw Screw Keyway Screw Blade Blade – Right Hand 300201 Socket Head Cap Screw (M12-1.75 x 110mm) 78824...
Page 31
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Head Unit: 976200-2, 976202-2 REV112019...
Page 32
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Head Unit: Item Part Name Part No. Item Part Name Part No. Motor 220V 300117 Bearing 300678 Screw Sealing Ring 300682 Stopping Block Bearing Cover 301333 (Not Shown) Washer 301336 Screw Head Ring...
Page 33
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Vise Unit: 976200-2, 976202-2 REV112019...
Page 34
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Vise Unit: Item Part Name Part No. Screw Set Screw Right Jaw Holder 300194 300876 Socket Cap Screw (M8-1.25 x 20mm) 80521 Set Screw Vise Slider Slider Side Cap Sealing Ring Gasket Cylinder Liner...
Page 35
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Non-Ferrous Head Unit: Item Part Name Part No. Item Part Name Part No. Motor – 220V 300117 Blade Shaft 300423 Spacer Spacer Cover Plate Upper Cog Pulley 79931 Bearing 300426 Washer Gasket...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Items not shown: Part Name Part No. Part Name Part No. Hood Limit Switch 300212 Valve for Regulating Feed Vise 300195 Air Feed Regulator 300356 Table Cover Plate 300198 4-Way Valve 79914 Hex Wrench...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com DEACTIVATING THE MACHINE If the machine is not going to be in use for a long period of time it is recommended that you do the following: 1. Unplug machine. 2.