Field Settings Table 1-2 - Daikin EGSQH10S18AA9W Service Manual

ESIE13-03 | Part 5. Appendix
Field settings table
Breadcrumb Field code Setting name
A.6.6 Are you sure you want to activate the forced defrost function?
Brine freezeup temperature
A.6.9 [A-04]
Boiler efficiency
A.6.A [7-05]
Overview settings
A.8 [0-00] Leaving water value for high ambient temp. for LWT add zone heating WD curve.
A.8 [0-01] Leaving water value for low ambient temp. for LWT add zone heating WD curve.
A.8 [0-02] High ambient temp. for LWT add zone heating WD curve.
A.8 [0-03] Low ambient temp. for LWT add zone heating WD curve.
A.8 [0-04] --
A.8 [0-05] --
A.8 [0-06] --
A.8 [0-07] --
A.8 [0-0B] Leaving water value for high ambient temp. for DHW WD curve.
A.8 [0-0C] Leaving water value for low ambient temp. for DHW WD curve.
A.8 [0-0D] High ambient temp. for DHW WD curve.
A.8 [0-0E] Low ambient temp. for DHW WD curve.
A.8 [1-00] Low ambient temp. for LWT main zone heating WD curve.
A.8 [1-01] High ambient temp. for LWT main zone heating WD curve.
A.8 [1-02] Leaving water value for low ambient temp. for LWT main zone heating WD curve.
A.8 [1-03] Leaving water value for high ambient temp. for LWT main zone heating WD curve.
A.8 [1-04] --
A.8 [1-05] --
A.8 [1-06] --
A.8 [1-07] --
A.8 [1-08] --
A.8 [1-09] --
A.8 [1-0A] What is the averaging time for the outdoor temp?
A.8 [2-00] When should the disinfection function be executed?
A.8 [2-01] Should the disinfection function be executed?
A.8 [2-02] When should the disinfection function start?
A.8 [2-03] What is the disinfection target temperature?
A.8 [2-04] How long must the tank temperature be maintained?
A.8 [2-05] Room antifrost temperature
A.8 [2-06] Room frost protection
A.8 [2-09] Adjust the offset on the measured room temperature
A.8 [2-0A] Adjust the offset on the measured room temperature
A.8 [2-0B] What is the required offset on the measured outdoor temp.?
A.8 [3-00] Is auto restart of the unit allowed?
A.8 [3-01] --
A.8 [3-02] --
A.8 [3-03] --
A.8 [3-04] --
A.8 [3-05] --
A.8 [3-06] What is the maximum desired room temperature in heating?
A.8 [3-07] What is the mimimum desired room temperature in heating?
A.8 [3-08] --
A.8 [3-09] --
A.8 [4-00] What is the BUH operation mode?
A.8 [4-01] --
A.8 [4-02] Below which outdoor
temperature is heating allowed?
A.8 [4-03] --
A.8 [4-04] --
A.8 [4-05] --
A.8 [4-06] --
(*) This setting is not applicable for this unit. Do not change the default value.
13/05/15 | Version 2.0
Figure 71 - Field settings table 1-2
Installer setting at variance with
default value
Range, step Date Value
Default value
R/W (*)
R/W 0: 0°C
1: -2°C
2: -4°C
3: -6°C
4: -8°C
5: -10°C
6: -12°C
7: -14°C
R/W 0: Very high (*)
1: High
2: Medium
3: Low
4: Very low
R/W [9-05]~min(45,[9-06])°C, step: 1°C
25°C
R/W [9-05]~[9-06]°C, step: 1°C
60°C
R/W 10~20°C, step: 1°C
15°C
R/W -20~5°C, step: 1°C
-20°C
R/W 8
R/W 12
R/W 35
R/W 20
R/W 35~[6-0E]°C, step: 1°C
45°C
R/W 45~[6-0E]°C, step: 1°C
60°C
R/W 10~20°C, step: 1°C
15°C
R/W -20~5°C, step: 1°C
-20°C
R/W -20~5°C, step: 1°C
-20°C
R/W 10~20°C, step: 1°C
15°C
R/W [9-00]~[9-01], step: 1°C
60°C
R/W [9-00]~min(45,[9-01]), step: 1°C
25°C
R/W 0
R/W 0
R/W
20
R/W 35
R/W 22
R/W 18
R/W
0: No averaging
1: 12 hours
2: 24 hours
3: 48 hours
4: 72 hours
R/W 0: Each day
1: Monday
2: Tuesday
3: Wednesday
4: Thursday
5: Friday
6: Saturday
7: Sunday
R/W 0: No
1: Yes
R/W 0~23 hour, step: 1 hour
23
R/W 60°C
R/W 60 min
R/W
4~16°C, step: 1°C
12°C
R/W 0: Disabled
1: Enabled
R/W -5~5°C, step: 0,5°C
0°C
R/W -5~5°C, step: 0,5°C
0°C
R/W -5~5°C, step: 0,5°C
0°C
R/W 0: No
1: Yes
R/W 0
R/W 1
R/W 4
R/W
2
R/W 1
R/W 18~30°C, step: A.3.2.4
30°C
R/W 12~18°C, step: A.3.2.4
12°C
R/W 35
R/W 15
R/W 0: Limit
1: Enable
2: Only DHW
R/O 0
R/W 14~35°C, step: 1°C
35°C
R/W 3
R/W 2
R/W 0
R/W 0
Ground source heat pump
Field settings table
Breadcrumb Field code Setting name
A.8 [4-07] Enable the second step of the backup heater?
A.8 [4-08] Which power limitation mode is required on the system?
A.8 [4-09] Which power limitation type is required?
A.8 [4-0B] --
A.8 [4-0D] --
A.8 [5-00] Is backup heater or boiler operation allowed above equilibrium
temperature during space heating operation?
A.8 [5-01] What is the equilibrium temperature for the building?
A.8 [5-02] --
A.8 [5-03] --
A.8 [5-04] --
A.8 [5-05] What is the requested limit for DI1?
A.8 [5-06] What is the requested limit for DI2?
A.8 [5-07] What is the requested limit for DI3?
A.8 [5-08] What is the requested limit for DI4?
A.8 [5-09] What is the requested limit for DI1?
A.8 [5-0A] What is the requested limit for DI2?
A.8 [5-0B] What is the requested limit for DI3?
A.8 [5-0C] What is the requested limit for DI4?
A.8 [5-0D] What type of backup heater installation is used?
A.8 [5-0E] --
A.8 [6-00] The temperature difference determining the heat pump ON temperature.
A.8 [6-01] The temperature difference determining the heat pump OFF temperature.
A.8 [6-02] --
A.8 [6-03] What is the capacity of the backup heater step 1?
A.8 [6-04] What is the capacity of the backup heater step 2?
A.8 [6-05] --
A.8 [6-06] --
A.8 [6-07] --
A.8 [6-08] Reheat hysteresis
A.8 [6-09] --
A.8 [6-0A] What is the desired comfort storage temperature?
A.8 [6-0B] What is the desired eco storage temperature?
A.8 [6-0C] What is the desired reheat temperature?
A.8 [6-0D] What is the desired setpoint mode in DHW?
A.8 [6-0E] What is the maximum tank temperature setpoint?
A.8 [7-00] --
A.8 [7-01] --
A.8 [7-02] How many leaving water temperature zones are there?
A.8 [7-03] PE factor
A.8 [7-04] --
A.8 [7-05] Boiler efficiency
A.8 [8-00] Minimum running time for domestic hot water operation.
A.8 [8-01] Maximum running time for domestic hot water operation.
A.8 [8-02] Anti-recycling time.
A.8 [8-03] --
A.8 [8-04] Additional running time for the maximum running time.
A.8 [8-05] Allow modulation of the LWT to control the room?
A.8 [8-06] Leaving water temperature maximum modulation.
A.8 [8-07] --
A.8 [8-08] --
A.8 [8-09] What is the desired comfort main LWT in heating?
A.8 [8-0A] What is the desired eco main LWT in heating?
A.8 [8-0B] --
A.8 [8-0C] --
A.8 [8-0D] --
A.8 [9-00] What is the maximum desired LWT for main zone in heating?
A.8 [9-01] What is the mimimum desired LWT for main zone in heating?
A.8 [9-02] --
A.8 [9-03] --
A.8 [9-04] --
A.8 [9-05] What is the mimimum desired LWT for add. zone in heating?
A.8 [9-06] What is the maximum desired LWT for add. zone in heating?
A.8 [9-07] --
(*) This setting is not applicable for this unit. Do not change the default value.
1. Field settings
Installer setting at variance with
default value
Range, step Date Value
Default value
R/W 0: No
1: Yes
R/W
0: No limitation
1: Continuous
2: Digital inputs
R/W 0: Current
1: Power
R/W 1
R/W 3
R/W 0: Allowed
1: Not allowed
R/W -15~35°C, step: 1°C
0°C
R/O 0
R/W 0
R/W 10
R/W 0~50 A, step: 1 A
50 A
R/W 0~50 A, step: 1 A
50 A
R/W 0~50 A, step: 1 A
50 A
R/W 0~50 A, step: 1 A
50 A
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/W 0~20 kW, step: 0,5 kW
20 kW
R/O 4: 3PN,(1/2)
R/W 1
R/W 2~20°C, step: 1°C
2°C
R/W 0~10°C, step: 1°C
2°C
R/W 0
R/W 0~10kW, step: 0,2kW
3kW
R/W 0~10kW, step: 0,2kW
3kW
R/W 0
R/W
0
R/W 0
R/W 2~20°C, step: 1°C
10°C
R/W
0
R/W 30~[6-0E]°C, step: 1°C
60°C
R/W 30~min(50, [6-0E]) °C, step: 1°C
45°C
R/W 30~min(50, [6-0E]) °C, step: 1°C
45°C
R/W 0: Reheat only
1: Reheat + sched.
2: Scheduled only
R/W 60°C
R/W 0
R/W 2
R/W 0: 1 LWT zone
1: 2 LWT zones
R/W 0~6, step: 0,1
2,5
R/W 0
R/W 0: Very high (*)
1: High
2: Medium
3: Low
4: Very low
R/W 0~20 min, step: 1 min
5 min
R/W 5~95 min, step: 5 min
30 min
R/W 0~10 hour, step: 0,5 hour
0,5 hour
R/W 50
R/W 0~95 min, step: 5 min
95 min
R/W 0: No
1: Yes
R/W
1~5°C, step: 1°C
3°C
R/W 18
R/W 20
R/W
[9-01]~[9-00], step: 1°C
55°C
R/W [9-01]~[9-00], step: 1°C
45°C
R/W
13
R/W 10
R/W 10
R/W 37~65°C, step: 1°C
65°C
R/W 15~37°C, step: 1°C
24°C
R/W 22
R/W 5
R/W 1
R/W 15~37°C, step: 1°C
24°C
R/W 37~65°C, step: 1°C
65°C
R/W 5
Page 155