User Calibration Procedure; Mechanical Replacement Parts - Magnetrol E3A Modulevel Installation And Operating Manual

3.5.2 User Calibration Procedure

The E3 MODULEVEL is calibrated at the factory, so it normally requires only configuration by the user in the field.
Should the E3 require replacement of any parts in the field, a user calibration must be performed after changing out any of
the following original parts: Bezel assembly, LVDT assembly, range spring, stem assembly, or displacer. The following pro-
cedure should be followed when performing a user calibration in the field. Note: User calibration should be performed at
normal operating conditions. The factory calibration parameters will not be incorporated into the level measurement.
1. Move liquid level on displacer to desired low level point. Using keypad and LCD display, scroll down to DispFact.
2. Press to access data entry mode, down arrow until "Yes" is displayed and Enter again. The factory menu is now accessible.
3. Scroll down to CalSelct.
4. Press , then
5. Press to UserCalMenu then press
6. Scroll down to SnrCalLo.
7. Press , then
8. Scroll down to LvlCalLo. The default value is 0.00. If a different level value is desired at this point, press
, use the and
9. Move the liquid level on displacer to the desired high level point. Scroll to SnrCalHi.
10. Press , then
11. Scroll down to LvlCalHi. The default value is the displacer length. If a different level value is desired at this point, press
use the and

3.5.3 Mechanical Replacement Parts

Cage Temp.
Spring SG
Pressure Config.
Range
Rating 4th digit
0.23 – 0.54
A, B, C 0.55 – 1.09
1.10 – 2.20
0.23 – 0.54
D, E, F 0.55 – 1.09
1.10 – 2.20
150#,
0.23 – 0.54
300#
J, K, L 0.55 – 1.09
& 600#
1.10 – 2.20
ANSI
0.23 – 0.54
M, N, P
Temp ≤
0.55 – 1.09
+450°F
1.10 – 2.20
(+230°C)
0.23 – 0.54
M, N, P
Temp ≥
0.55 – 1.09
+500°F
1.10 – 2.20
(+260°C)
B
E
900#
0.55 – 1.09
ANSI
K
N
B
1500#
E
& 2500# 0.55 - 1.09
K
ANSI
N
N
150#
THRU
0.55 - 1.09
#600
E
N
900#
THRU
0.55 - 1.09
#2500
E
For Ultra High Temperature LVDT
36
until "User" is displayed and
to show the menu.
and simultaneously and
keys to choose the desired value and press
and simultaneously and
keys to choose the desired value and press
E-tube Kits
CSA, FM, ATEX, IEC
Carbon Steel Carbon Steel
089-5958-017 089-5958-002 089-5958-006
089-5958-019 089-5958-004 089-5958-008
089-5958-005 089-5958-001 089-5958-005
089-5958-018 089-5958-003 089-5958-007
089-5958-018 089-5958-003 089-5958-007
089-5958-020 089-5958-010 089-5958-014 089-5565-004
089-5958-022 089-5958-012 089-5958-016 089-5565-008
089-5958-013 089-5958-009 089-5958-013 089-5565-002
089-5958-021 089-5958-011 089-5958-015 089-5565-006
089-5958-020 089-5958-010
089-5958-022 089-5958-012
089-5958-013 089-5958-009
089-5958-021 089-5958-011
089-5958-027
089-5958-028
089-5958-027
089-5958-028
again.
again. The current liquid level has been captured as the low level point.
again.
again. The current liquid level has been captured as the high level point.
again. The user calibration is complete.
14
CSA, FM,
Stem Kit*
ATEX, IEC,
316 SS
089-5565-004 089-5340-002
089-5565-003 089-5340-005
089-5565-003 089-5340-008
089-5565-008 089-5340-003
089-5565-007 089-5340-006
089-5565-007 089-5340-009
089-5565-002 089-5340-002 089-5340-001
089-5565-001 089-5340-005 089-5340-004
089-5565-001 089-5340-008 089-5340-007
089-5565-006 089-5340-002
089-5565-005 089-5340-005
089-5565-005 089-5340-008
089-5565-006 089-5340-003
089-5565-005 089-5340-006
089-5565-005 089-5340-009
089-5565-004
089-5565-008
n/a
089-5565-002
089-5565-006
089-5565-013** 089-5340-011
089-5565-015**
089-5565-014** 089-5340-011
089-5565-016**
*
Field replacement of this part requires a user calibration of the repaired unit.
**
For ultra high temperature LVDT stem kits, LVDT core is not included.
48-635 E3 Modulevel
Spring Kits*
Inconel
®
15
089-5340-010
® Displacer Level Transmitter
,
16
316 SS
n/a
n/a
n/a
n/a