V-Link Settings; Resetting The Image - Roland MC-909 Owner's Manual

V-LINK settings

Parameter Range
Note Tx Ch 1–16
Clip 1 Note No. 0(C-1)–127(G9)
Play Speed Ctrl 0.0–1.0–2.0, 0.5–1.0–2.0,
0.0–1.0–4.0, 0.5–1.0–4.0,
0.0–1.0–8.0, 0.5–1.0–8.0,
0.0–1.0–16.0, 0.5–1.0–16.0,
0.0–1.0–32.0, 0.5–1.0–32.0,
0.0–2.0–4.0, 0.0–4.0–8.0,
0.0–8.0–16.0, 0.0–16.0–32.0,
-2.0–1.0–4.0, -6.0–1.0–8.0
Dissolve Time OFF, CC1, CC5, CC7, CC10,
CC11, CC71–74, CC91–93,
Channel Aftertouch
Ctrl Tx Ch 1–16
Color Cb Ctrl OFF, CC1, CC5, CC7, CC10,
Color Cr Ctrl CC11, CC71–74, CC91–93,
Brightness Ctrl Channel Aftertouch
VFX1–4 Ctrl
Fade Ctrl
PAD MODE CLIP, PALETTE
Local Sw OFF, ON
(OFF), ✔ (ON)
Clip filter
(check boxes 1–32)
Using the Clip Filter
For example, suppose that of the rhythm set you input in the
part used for V-LINK (i.e., the part of the same number as the
Note Tx Channel), you want only the kick and snare to switch
clips. In this case, check only the clips that correspond to the
note numbers of the kick and snare. The clips will switch when
the kick or snare plays.
Explanation
MIDI channel that will switch Edirol DV-7PR clips/palettes and will control dissolve time.
Note number (velocity pad) that corresponds to Edirol DV-7PR clip 1
If this is set to 59 (B3), velocity pads 1–16 will correspond to clips 1–16.
Range of video playback speed
The three values are the playback speeds (multiples of normal speed) at the negative,
center, and positive positions of the turntable emulation slider.
Control change number that controls the dissolve time (time over which the image switch-
es)
MIDI channel that will control the Edirol DV-7PR color Cb/Cr, brightness, and video effect
switching
Control change number that controls the Cb color of the image
Control change number that controls the Cr color of the image
Control change number that controls the brightness of the image
Control change number that controls the video effect
* VFX2–4 are not supported by the Edirol DV-7PR.
Control change number that controls the output fade
Selects whether the velocity pads will switch clips or palettes.
Press [F1 (Clip mode)]: switch clips
Press [F2 (Palette)]: switch palettes
Specifies whether the internal sound generator is disconnected (OFF) from the velocity
pads, or not (OFF).
Enable/disable switching for each clip
Clips that are checked can be switched (see explanatory box below)

Resetting the image

[F3 (Clip Reset)]
[F4 (All Reset)]
* For details on clips/palettes, dissolve time, color difference signals (Cb/
Cr), refer to the Edirol DV-7PR manual.
The MC-909 does not support the Edirol DV-7PR's dual stream
mode.
About V-LINK
Turn off the image (solid black).
The effect applied to the image will be reset,
and brightness, color difference, etc. will all
return to the default value.
139