Step 10. Install Volcanic Stone; Embers & Logs - Superior SSBV-3530CNM Installation Instructions Manual

Step 10. INSTALL VOLCANIC STONE,

GLOWING EMBERS AND LOGS
1. Remove the front glass enclosure panel
(see Glass Door Panel Removal Instructions
on Page 17).
2. Carefully remove the log set box from
the fi rebox. Next, remove embers and
volcanic stone from the control compart-
ment. Handle logs carefully to prevent
breakage.
3. Install decorative volcanic stone - Mound up
a portion of the volcanic stone in front of the
burner in a pleasing pattern.
4. Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see Figure 26).
Keep the pieces fl uffed up, not matted.
Distribute these pieces over the surface of
the burner, as shown in Figures 27 or 28.
Do not use more than is necessary. Ensure
that the main burner slots remain uncovered
by the ember material.
Note: This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time. For
f i r e - p a r t s . c o m
best glowing effect, replace the ember material
annually.
5. Placement of Logs -
The logs have locating notches or slots to
help ensure that they are properly positioned.
Proper log placement is critical to prevent
sooting.
Glowing Embers
Separate into Quarter
Size (separate) Pieces
Bag of Glowing
Embers (rockwool)
Figure 26
REFERENCE
Firebox Accessories / Parts
Cat. No. Model No.
Bag of Glowing Embers
88L53 FGE
(1 oz. rockwool)
Bag of Decorative
80L42 FDVS
Volcanic Stone
Table 10
14
SSBV-3530 - Install as Follows
Carefully position the ceramic fi ber logs into the
fi rebox as shown in Figure 27. Logs should be
placed in the order shown and per the following
instructions.
1. Place embers on the front burner tube and
volcanic stone in front of the burner as
shown and per instructions on this Page
(see Placement of Glowing Embers & Install
Decorative Volcanic Stone on this Page).
2. Place the rear log (A) as shown. Position
the 2 notches on the bottom of log (A) over
the 2 corresponding locating brackets as
shown.
3. Place the center log (C) as shown. The 2
notches on the bottom of log (C) fi t over
the corresponding locating brackets.
4. Place the left log (B) as shown. The top fork
on log (B) fi ts into the notch on log (A). The
bottom of log (B) rests on the subfl oor.
5. Place the top fork on log (D) into notch on
log (A) as shown. The bottom fork on log
(D) rests on the subfl oor fl ange (identifi ed
in photo #1).
SSBV-4035 - Install as Follows
Carefully position the ceramic fi ber logs into the
fi rebox as shown in Figure 28. Logs should be
placed in the order shown and per the following
instructions.
1. Place embers on the front burner tube and
volcanic stone in front of the burner as
shown and per instructions on this Page
(see Placement of Glowing Embers & Install
Decorative Volcanic Stone on this page).
2. Place the rear log (A) as shown. Position
the 2 notches on the bottom of the log over
the 2 corresponding locating brackets as
shown.
3. Place the center log (C) as shown. The 2
notches on the bottom of the log fi t over
the corresponding locating brackets.
Description
4. Place the top right log (D) as shown. The top
fork on log (D) fi ts into notch on log (A) as
shown. The bottom fork on log (D) rests on
subfl oor fl ange (identifi ed in photo #1).
5. Place the top left log (B) as shown. The top
fork on log (B) fi ts into notch on log (A). The
bottom of the log rests on the subfl oor.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
WARNING
If logs are not installed according
to the log installation instruc-
tions, fl ame impingement and
improper combustion could
occur and result in soot and/or
excessive production of carbon
monoxide (CO), a colorless,
odorless, toxic gas.
WARNING
DO NOT attempt to install the
logs until the appliance instal-
lation has been completed, the
gas line connected and tested
for leaks and the initial burner
operation has been checked
out.
WARNING
The size and position of the log
set is critical to achieve a safe,
reliable and attractive fl ame
pattern. Any attempt to use a
different log set in the fi replace
will void the warranty and will
result in incomplete combus-
tion, sooting, and poor fl ame
quality.
WARNING
This appliance is not designed
to burn wood. Any attempt to
do so could cause irreparable
damage to appliance and prove
hazardous to your safety.