Ametek 7270 Instruction Manual page 222

INDEX
NN[.] command 6-19, E-17
NNBUF [n] command 6-15, E-17
Noise Buffer Length control 5-30
Noise Measurement Mode 5-30
Noise measurements 3-13
NOISEMODE [n] command 6-15, E-17
OA[.] [n] command 6-20, E-17
OF[.] [n] command 6-21, E-17
Operating environment 2-1
Operating Modes 3-1
Options Menu 5-37
OSC OUT connector 4-1
Oscillator
amplitude control 5-8, 5-19, 5-22, 5-63, 5-82
amplitude modulation 3-10
amplitude modulation enabled control 5-25
Amplitude Modulation Menu 5-24
amplitude modulation source control 5-25
Amplitude Sweep Menu 5-22
center frequency control 5-26
center voltage control 5-24, 5-26
filter control 5-25, 5-26
frequency control 5-8, 5-19, 5-20, 5-24, 5-63, 5-
81
frequency modulation 3-10
Frequency Modulation Menu 5-25
frequency span control 5-26
Frequency Sweep Menu 5-19
frequency sweeps - general 3-9
modulation depth control 5-24
Oscillator Menu 5-18
output amplitude sweeps - general 3-9
output update rate 3-9
overview 3-9
start amplitude control 5-22
start frequency control 5-20
step amplitude control 5-23
step size control 5-20
stop amplitude control 5-23
stop frequency control 5-20
synchronous oscillator control 5-19
time/step amplitude control 5-23
time/step size control 5-20
VCO enabled control 5-26
VCO Menu 5-25
voltage span control 5-25, 5-26
Output
expand control 5-16
filter slope 2 control 5-87
filter slope control 5-14, 5-68, 5-69, 5-85
offset 5-7, 5-62, 5-81
INDEX-4
offset status control 5-16, 5-70, 5-71, 5-87, 5-89
output expansion 3-12
output offset 3-12
sync time constant control 5-68, 5-85
time constant 2 control 5-86
time constant control 5-14, 5-68, 5-69, 5-85
time constant mode 5-14, 5-15, 5-68, 5-86
X1-channel offset control 5-70, 5-87
X2-channel offset control 5-71, 5-88
X-channel offset control 5-15
Y1-channel offset control 5-70, 5-87
Y2-channel offset control 5-71, 5-88
Y-channel offset control 5-15
Overload
input overload indicator 5-5
output overload indicator 5-5
PAGE [n] command 6-36, E-17
PHA[.] command 6-18, E-18
PHASEPOL [n] command 6-18, E-18
PORTDIR [n] command 6-25, E-18
Power-up defaults 3-17
PRE AMP POWER connector 4-7
Rack mounting 2-1
Ratio output 5-53, 5-77
READBYTE command 6-26, E-18
Rear Panel
layout 4-6
REF IN connector 4-1
REF MON connector 4-7
Reference 1 harmonic control 5-84
Reference 1 phase control 5-66
Reference 1 source control 5-66
Reference 2 harmonic control 5-63, 5-84
Reference 2 phase control 5-66
Reference 2 source control 5-66
Reference channel inputs 3-7
Reference channel, overview 3-7
Reference harmonic 1 control 5-81
Reference harmonic 2 control 5-81
Reference harmonic control 5-7, 5-13
Reference Lock indicator 5-5
Reference mode
external 3-2, 3-8
internal 3-2, 3-8
Reference phase control 5-7, 5-13, 5-62
Reference phase quadrant control 5-7, 5-13
Reference phase shifter 3-8
Reference source control 5-13, 5-84
REFMODE [n] command 6-13, E-18
REFN [n] command 6-14, E-19
REFP[.] [n] command 6-14, E-19