Serial Communications Look-Up Table; Trip Group Catergories; Dc Voltage Trip And Restart Levels - Emerson SP1201 Installation Manual

Safety Product
Introduction
Information information
Table 12-3 Serial communications look-up table
No.
1
2
3
5
6
8
9
10
20
21
22
23
24
25
26
27
28
29
30
31
34
35
36
37 to 38
39
40 to 89
Table 12-4 Trip group catergories
Category
Hardware faults
Self resetting trips
Non-resettable trips HF20 to HF30, SL1.HF, SL2.HF, SL3.HF Cannot be reset.
EEF trip
Normal trips
Normal trips with
extended reset
Low priority trips
Phase loss
Drive over-heat
based on thermal
model
Table 12-5 DC voltage trip and restart levels
Drive voltage rating UU trip level Vdc UU restart level Vdc
200
400
575
690
214
System Mechanical
design installation
Trip No.
UU 90
OU 91
OI.AC 92
PS 93
Et 94
PS.10V 95
PS.24V 96
t010 97
It.AC 98
O.ht1 99
O.ht2 100
O.CtL 102
th 104
thS 105
O.Ld1 106
O.ht3 108
CL2 109
CL3 110
SCL 111 to 160
EEF 168 to 175
Pad 177 to 178
CL.bit 179
EEF1 180
t036 to t038 181
Ll.SYNC 182
t040 to t089 183
Trips
HF01 to HF19
UU
EEF
All other trips
OI.AC, x.OIAC,
Old1, cL2, cL3, SCL
PH
O.ht3
175 215
330 425
435 590
435 590
www.controltechniques.com
Electrical Getting
Optimisation
installation started
Trip
UP div0
UP PAr
UP ro
UP So
UP ovr
UP OFL
UP uSEr
UP udf
UP ACC
t099
Oht4.P
OIAC.P
Oht2.P
OV.P
PS.P
OIdC.P
Unid.P
t111 to t160
t168 to t175
t177 to t178
C.Chg
C.Optn
C.RdO
C.Err
C.dat
These indicate fatal problems and cannot be reset. The drive is inactive after one of
these trips and the display shows HFxx.
Under voltage trip cannot be reset by the user, but is automatically reset by the
drive when the supply voltage is with specification.*
Cannot be reset unless a code to load defaults is first entered in Pr x.00 or Pr 11.43.
Can be reset after 1.0s
Can be reset after 10.0s
If Pr 10.37 is 1 or 3 the drive will stop before tripping.
The drive stops before tripping provided the drive motoring power is suitably
reduced after 500ms of detecting phase loss
The drive stops before tripping, but if it does not stop within 10s the drive will
automatically trip.
Technical Component
Parameters
data sizing
No.
184
185
186
187
188
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216 to 217
220 to 232 HF20 to HF32
Comments
Unidrive SP Regen Installation Guide
Diagnostics
Trip
C.FULL
C.Acc
C.rtg
C.Typ
C.cpr
DESt
SL1.HF
SL1.tO
SL1.Er
SL1.nF
SL1.dF
SL2.HF
SL2.tO
SL2.Er
SL2.nF
SL2.dF
SL3.HF
SL3.tO
SL3.Er
SL3.nF
SL3.dF
SL.rtd
t216 to t217
Issue Number: 2