Lauda Integral XT 150 Operating Instructions Manual page 7

Integral XT
7.6.3.2 Permanently and automatic degassing ................................................................................... 54
7.6.4 Topping up ...................................................................................................................................... 54
7.7 D
RAINING
7.8 C
HANGING THE HEAT TRANSFER LIQUID AND INTERNAL CLEANING
7.9 I
MPORTANT SETTINGS
7.9.1 Temperature setpoint setting .......................................................................................................... 57
7.9.2 Displaying the actual external temperature .................................................................................... 59
7.9.3 Pump capacity or setting standby ................................................................................................... 60
7.9.4 Pressure control .............................................................................................................................. 62
7.9.5 Maximum pressure control .............................................................................................................. 62
7.9.6 Activating external control ............................................................................................................... 63
7.9.7 Current consumption from the mains .............................................................................................. 65
7.9.8 Setting the date and time (Command remote control) .................................................................... 66
7.9.9 Display resolution setting (Command remote control) .................................................................... 67
7.10 S
PECIAL SETTINGS
7.10.1 Defining the type of start mode ....................................................................................................... 68
7.10.2 Defining temperature limits ............................................................................................................. 69
7.10.3 Setpoint offset operating mode ....................................................................................................... 70
7.10.4 Restoring works settings ................................................................................................................. 71
7.10.5 Setting the volume of the acoustic signals ...................................................................................... 72
7.10.6 Entering the offset of the internal temperature probe ..................................................................... 72
7.10.7 Restoring the works setting of the internal temperature-probe offset ............................................. 73
7.10.8 Entering the offset of the external temperature probe .................................................................... 74
7.10.9 Restoring the works setting of the external temperature-probe offset ............................................ 74
7.10.10 SmartCool ....................................................................................................................................... 75
7.11 G
RAPHICAL DISPLAY OF TEMPERATURE MEASUREMENTS
7.12 P
ROGRAMMER
7.12.1 Program example ............................................................................................................................ 78
7.12.2 Selecting and starting the program (Start, Hold, Stop) ................................................................... 80
7.12.3 Interrupting, continuing or terminating the program (Hold, Continue, Stop) ................................... 81
7.12.4 Creating or modifying a program (Edit) ........................................................................................... 82
7.12.5 Defining the number of program loops (Loops) .............................................................................. 86
7.12.6 Viewing the program sequence as a graph (Graph) ....................................................................... 86
7.12.7 Obtaining information on a program (Info) ...................................................................................... 87
7.12.8 Optimization of the Programmer ..................................................................................................... 88
7.13 R
AMP FUNCTION
7.14 T
IMER FUNCTION
7.15 C
ONTROL AND
7.15.1 Setting instructions for bypass ........................................................................................................ 92
7.15.2 Configuration examples .................................................................................................................. 93
7.15.3 Internal control variable (integral measurement probe) .................................................................. 94
7.15.3.1 Procedure for setting the control parameters for internal control ............................................ 95
7.15.3.2 Table with control parameters and pump level for internal control .......................................... 95
7.15.4 External control variable (External measurement probe) ............................................................... 96
7.15.4.1 Procedure for setting the control parameters for external control ........................................... 97
7.15.4.2 Well-proven settings for control parameters and pump level for external control ................... 99
7.15.5 Internal and external control parameter sets .................................................................................. 99
7.15.6 Self Adaption ................................................................................................................................. 101
7.15.7 Limiting the heating and cooling power ......................................................................................... 103
7.15.7.1 Actuating signal limit .............................................................................................................. 103
7.15.7.2 Dynamic limitation of heating power ...................................................................................... 103
7.15.7.3 Dynamic control of heating power ......................................................................................... 104
7.16 A , W
LARMS
7.16.1 Overtemperature protection and checking .................................................................................... 105
7.16.2 Low-level alarm and low-level checking ........................................................................................ 106
7.16.3 High-level settings ......................................................................................................................... 107
7.16.4 High-level warning or alarm .......................................................................................................... 108
7.16.5 Pump-motor supervision: Overload or blockage ........................................................................... 109
YAWE0028 / 24/06/2016
......................................................................................................................................... 55
....................................................................................................................... 57
............................................................................................................................ 68
.................................................................................................................................. 78
............................................................................................................................... 89
/ T (C
IMER OMMAND
C
ONTROL PARAMETERS
E
ARNINGS AND RRORS
(C
OMMAND REMOTE CONTROL
) ................................................................................................ 90
.............................................................................................. 91
.................................................................................................. 105
Contents
........................................................ 56
) ..................... 76
5