Manitowoc Grove RT9130E Product Manual page 21

ft luffing folding boom extension with or inserts fixed angle
ft ft
ft LENGTH WITH
°
OFFSET
Feet
����
��
����
����
��
����
����
��
���.��
����
��
���.��
����
��
����
����
��
����
����
���
���.��
����
���
���.��
����
���
����
����
���
���.��
����
���
����
����
���
����
����
���
���.��
����
���
����
����
���
���.��
����
���
����
����
���
���.��
����
���
����
����
���
���.��
����
���
����
����
���
����
����
���
���.��
���
°
��
Min. boom
angle for
indicated
length �no load�
Max. boom
length �ft� at
�° boom angle
�no load�
NOTE: � � Boom angles are in degrees.
�LMI operating code. Refer to LMI manual for operating instructions.
Grove RT E
The individual crane's load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane
ft ft , lb %
insert ft in
spread
Pounds
ft INSERT ft LENGTH WITH
° ° ° °
OFFSET OFFSET OFFSET OFFSET
����
����
���� ����
���� ���.��
���� ����
���.�� ���.��
���� ���� ����
���� ���.�� ����
���� ���� ���� ����
���� ���� ���.�� ���.��
���� ���� ���� ����
���.�� ���� ���� ���.��
���� ���� ���� ����
���.�� ���� ���� ���.��
���� ���� ���� ����
���� ���.�� ���� ����
���� ���� ���� ����
���.�� ���� ���.�� ����
���� ���� ���� ����
���� ���.�� ���.�� ����
���� ���� ���� ����
���� ���� ���.�� ���.��
���� ���� ���� ����
���.�� ���.�� ���� ���.��
���� ���� ���� ����
���� ���� ���� ����
���� ���� ���� ����
���.�� ���.�� ���.�� ����
���� ���� ���� ����
���� ���� ���.�� ���.��
���� ���� ���� ����
���.�� ���.�� ���� ����
���� ���� ���� ����
���� ���.�� ���.�� ����
���� ���� ���� ����
���.�� ���� ���.�� ���.��
���� ���� ���� ����
���.�� ���.�� ���� ����
���� ���� ����
���� ���.�� ����
���� ���� ����
���� ���.�� ���.��
���� ����
���.�� ���.��
° ° ° °
�� �� �� ��
�� ft �� ft
A������������
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
ft main boom
NOTES:
. All capacities above the bold line are based on
° structural strength of boom extension and do
not exceed
with SAE J
. ft folding boom extension length may be
used for single line lifting service only.
ft INSERT
NOTE: Lifting with the
°
either one or two
OFFSET
not permitted.
. For main boom lengths less than
the boom extension erected, the rated loads
are determined by boom angle. Use only
the column which corresponds to the boom
extension length and offset for which the
machine is set up. For boom angles not shown,
use the rating of the next lower boom angle.
. WARNING: Operation of this machine with
heavier loads than the capacities listed is
strictly prohibited. Machine tipping with boom
extension occurs rapidly and without advance
warning.
����
. Boom angle is the angle above or below
����
horizontal of the longitudinal axis of the boom
����
base section after lifting rated load.
����
����
. Capacities listed are with outriggers properly
���.��
extended and vertical jacks set only.
����
���.��
����
����
����
����
����
���.��
����
����
����
����
����
���.��
����
����
����
���.��
����
���.��
����
����
����
���.��
����
����
°
��
Load chart
% of tipping loads, in accordance
.
ft extension base with
ft insert sections installed is
ft with