Manitowoc Grove RT9130E Product Manual page 14

Load chart
ft ft ft or ft
Insert
Pounds
ft LENGTH WITH ft INSERT
° °
OFFSET OFFSET OFFSET
Feet
����
��
����
����
��
���.��
����
��
���.��
����
��
����
���� ����
��
���� ����
���� ����
��
���.�� ���.��
���� ����
��
���.�� ����
���� ���� ����
��
���� ���� ����
���� ���� ����
���
���� ���.�� ����
���� ���� ����
���
���.�� ���.�� ����
���� ���� ����
���
���� ���� ���.��
���� ���� ����
���
���� ���.�� ����
���� ���� ����
���
���.�� ���� ���.��
���� ���� ����
���
���� ���� ����
���� ���� ����
���
���.�� ���.�� ���.��
���� ���� ����
���
���.�� ���� ����
���� ���� ����
���
���� ���.�� ���.��
���� ���� ����
���
���.�� ���� ����
���� ���� ����
���
���� ���.�� ���.��
���� ���� ����
���
���.�� ���� ���.��
���� ���� ����
���
���.�� ���.�� ����
���� ���� ����
���
���� ���.�� ���.��
���� ���� ����
���
���.�� ���� ���.��
���� ���� ����
���
���.�� ���� ���.��
���� ����
���
���.�� ���.��
���� ����
���
���.�� ���.��
Min. boom
�� ��
angle
for indicated
length
�no load�
Max. boom
��
length �ft� at
�° boom angle
�no load�
NOTE: �� Boom angles are in degrees
�LMI operating code. Refer to LMI for operating instructions
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
The individual crane's load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
°
, lb %
ft in
spread
ft LENGTH WITH ft INSERT
° ° ° °
OFFSET OFFSET OFFSET
����
����
����
���.��
����
���.��
����
���.��
���� ����
���.�� ����
���� ����
���� ���.��
���� ����
���� ���.��
���� ���� ����
���� ���.�� ����
���� ���� ����
���.�� ���� ����
���� ���� ����
���.�� ���� ���.��
���� ���� ����
���.�� ���� ���.��
���� ���� ����
���� ���.�� ����
���� ���� ����
���� ���.�� ����
���� ���� ����
���.�� ���� ���.��
���� ���� ����
���.�� ���� ����
���� ���� ����
���� ���.�� ����
���� ���� ����
���� ���� ���.��
���� ���� ����
����
���.�� ����
���� ���� ����
���� ���.�� ���.��
���� ���� ����
���� ���� ���.��
���� ����
���� ����
���� ����
���.�� ���.��
����
����
�� �� �� ��
��
A ������������A
NOTES:
. All capacities above the bold line are based
on structural strength of boom extension
and do not exceed % of tipping loads, in
accordance with SAE J .
. ft folding boom extension length may be
used for single line lifting service only.
Note: Lifting with the ft extension base
with either one or two ft insert sections
installed is not permitted.
. For main boom lengths less than
with the boom extension erected, the rated
loads are determined by boom angle. Use
only the column which corresponds to the
boom extension length and offset for which
the machine is set up. For boom angles not
shown, use the rating of the next lower boom
angle.
. WARNING: Operation of this machine with
heavier loads than the capacities listed is
strictly prohibited. Machine tipping with
boom extension occurs rapidly and without
advance warning.
. Boom angle is the angle above or below
horizontal of the longitudinal axis of the
boom base section after lifting rated load.
. Capacities listed are with outriggers properly
extended and vertical jacks set only.
ft