Ingenico IWL2 series User Manual page 13

This equipment complies with Part 68 of the FCC rules and the requirements adopted by
the ACTA. On the bottom of this equipment is a label that contains, among other
information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this
nu mber must be provided to the telephone company.
This equipment uses the following USOC jacks: (RJ11C).
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted by
the ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
The REN is used to determine the number of devices that may be connected to a telephone
line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To
be certain of the number of devices that may be connected to a line, as determined by the
total RENs, contact the local telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify
you in advance that temporary discontinuance of service may be required. If advance notice
is not practical, the telephone company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of this equipment. If this happens, the
telephone company will provide advance notice in order for you to make the necessary
modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact Ingenico, or your local
INGENICO distributor or service center in the U.S.A. for repair and/or warrant information. If
the trouble is causing harm to the telephone network, the telephone company may request
you to remove this equipment from the network until the problem is resolved. No repairs
can be done by a customer on this equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure
the installation of this equipment does not disable your alarm equ ipment. If you have
qu estions about what will disable alarm equ ipment, consult your telephone company or a
qu alified installer.
•
No changes shall be made to the equipment without the permission of Ingenico as
this may void the user's authority to operate the equipment. / Tout changement
apporté à ce terminal non expressément approuvé par Ingenico est susceptible
d'annuler le droit de l'utilisateu r à se servir de cet équipement.
•
Service Center Information
The service center to be contacted is:
INGENICO North America
79 Torarrie Road
M3L 1G5 Toronto Ontario
Fax : +1 416 245 6701 tel : +1 416 245 6700
•
iWL2xx Wireless Series 25/32
900003061 R11 000 05/1122
Copyright © 2011 Ingenico
All rights reserved
FCC/IC Compliance (GSM/GPRS/3G model)
The FCC ID for IWL GSM/GPRS Terminal model is:
The FCC ID for IWL GSM/GPRS Contactless Terminal model is:
nu mber is:
2586D- IWL2XXGCL
The FCC ID for IWL 3G Contactless Terminal model is:
2586D- IWL3GCL
•
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equ ipment generates, uses and can radiate radio frequ ency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not
occur in a particu lar installation. If this equipment does cause harmful interference
to radio or television reception which can be determined by turning the equipment off
and on, the user is encou rag ed to try to correct interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equ ipment and receiver.
- Connect the equipment into an outlet on circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
•
In order to meet FCC and Industry Canada RF radiation exposu re limits for g eneral
population, this device must only be operated when held in the hand or in desktop
position with a minimum separation distance of at least 20cm from the user's body
and it must not be collocated or operated in conjunction with any other antenna or
transmitter. Use of this device with an accessory in order to be worn and operated
on user's body is strictly prohibited and will invalidate the certifications obtained for
FCC and Industry Canada.
•
Afin de respecter les directives de la FCC et d'Industrie Canada concernant les
expositions radiofréqu ence, cet appareil ne doit fonctionner que tenu dans la main
ou sur station d'accueil avec une distance minimale d'au moins 20cm du corps de
l'utilisateu r et il ne doit pas être en colocation ou coopération avec une autre
antenne ou émetteur. L'utilisation de cet appareil avec un accessoire dans le but
d'être porté et fonctionné sur le corps de l'utilisateur est strictement prohibé et
invalidera les certifications FCC et Industrie Canada obtenues
•
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
•
iWL2xx Wireless Series 26/32
900003061 R11 000 05/1122
XKB-IWL2XXG
and IC
XKB-IWL2XXGCL
and IC number is:
XKB-IWL2XX3GCL
Copyright © 2011 Ingenico
All rights reserved