Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Ingenico Manuals
  4. Payment Terminal
  5. iWL2 Series
  6. Quick start manual

Ingenico iWL2 Series Quick Start Manual

Mobile payment terminal
Hide thumbs Also See for iWL2 Series:
1
2
3
4

Advertisement

Quick Links

Download this manual See also: User Manual
Quick Start Guide
iWL2xx
GETTING STARTED
Set up your base unit in a convenient location close to a power
source and a telephone socket and/or an Ethernet socket.
To connect the base unit to a telephone point, remove the back
panel as shown in the diagram. Connect one end of the
telephone cable to the modem socket on your base unit
(marked IN), the other end should be plugged into an analogue
telephone line socket. To connect the Ethernet cable, connect
one side to your Ethernet socket or router and the other side to
the socket (marked ETH) on your base unit.
Note: If you connect both the telephone and Ethernet cables,
the Ethernet (Broadband) connection will be used in
preference. The Telephone connection may be used as a
backup. It is not recommended that the terminal is connected
to a phone line with call barring, call waiting or alarm enabled.
Finally, connect the power supply unit into the power socket on
your base unit and to the mains power. After a short
initialisation process, the terminal will display READY or an
idle logo. The terminal is ready to use.
Note: Press and hold the yellow clear key and the dot key
together to turn the terminal off.
SUPERVISOR PASSWORD
The default Supervisor Password is 01483. Please note: The
terminal will require you to change this to a new password of
your choosing before you can process any transactions.

FUNCTION KEYS

F1-F4 Keys: The function keys enable you to choose options
on screen and correspond to the labels displayed on the screen.
Menu Key: To enter the application menus press the Menu
key from the idle (READY) screen. Pressing the key again
moves to the next menu (if available).
Correction Keys: When entering numbers or letters, the
yellow clear key deletes one character at a time, while the red
cancel key deletes the entire line (this key also cancels
transactions).
Confirmation Key: The green enter key is used to confirm
anything that has been typed into the terminal.
Paper Feed Key: To test the feeding of the paper through the
printer press and hold the clear key.
See page 4 for instructions to change the paper roll.
Connecting the Base Unit
Base Unit Cover
Release
Clips
Telephone
Socket
Power Socket
(Modem)
01483
Ethernet
Socket

Advertisement

loading

Related Manuals for Ingenico iWL2 Series

Summary of Contents for Ingenico iWL2 Series

  • Page 1: Function Keys

    Quick Start Guide iWL2xx GETTING STARTED Connecting the Base Unit Set up your base unit in a convenient location close to a power Base Unit Cover source and a telephone socket and/or an Ethernet socket. To connect the base unit to a telephone point, remove the back Ethernet Release panel as shown in the diagram.
  • Page 2 THE CHIP CARD READER Customer cards must be inserted as shown, with the chip upwards. Push the card fully into the slot below the keypad and follow the instructions on screen. If you see a BAD READ message, check the card orientation and try again.
  • Page 3 CONTACTLESS - SALE From the idle screen, enter the sale amount for the transaction and press the enter key. For example enter £12.34 as 1234. If you make a mistake, press the clear key and re-enter the amount. The cardholder should present their card against the contactless symbol on the terminal display.

  • Page 4: Changing The Paper Roll

    This Quick Start Guide (DIV434769A) relates to terminal software APACS 4048 97.11.01 Whilst every effort has been made to ensure that the content of this document is accurate, Ingenico will not accept responsibility for any loss, damage or injury that may be incurred as a result of any errors or inaccuracies. The product is varied to suit an acquirer’s individual requirements and as such some features may vary or be disabled.