HP MSR Series Configuration Manual page 122

# After the link over which Router A and Router B communicates through the Layer 2 switch fails,
Router A quickly detects the change on Router B.
%Nov 12 18:34:48:823 2005 RouterA BFD/5/LOG: Sess[192.168.0.102/192.168.0.100,
Eth1/1], Sta : UP->DOWN, Diag: 1
%Nov 12 18:34:48:824 2005 RouterA RM/4/RMLOG:OSPF-NBRCHANGE: Process 1, Neighbour
192.168.0.102 (Ethernet1/1) from Full to Down
*0.50673825 RouterA BFD/8/SCM:Sess[192.168.0.102/192.168.0.100,Eth1/1],Oper: Reset
*0.50673825 RouterA BFD/8/EVENT:Send sess-down Msg, [Src:192.168.0.102,
Dst:192.168.0.100, Ethernet1/1] Protocol: OSPF
*0.50673826 RouterA RM/7/RMDEBUG:OSPF-BFD: Message Type rcv BFD down, Connect Type
direct-connect, Src IP Address 192.168.0.102, Src IFIndex 5, Dst IP Address
192.168.0.100
*0.50673827 RouterA RM/7/RMDEBUG:OSPF-BFD: Message Type delete session, Connect Type
direct-connect, Src IP Address 192.168.0.102, Src IFIndex 5, Dst IP Address
192.168.0.100
OSPF 1: Nbr 192.168.0.100 Rcv KillNbr State Full -> Down.
*0.50673829 RouterA BFD/8/EVENT:Receive Delete-sess, [Src:192.168.0.102,
Dst:192.168.0.100,Ethernet1/1], Direct, Proto:OSPF
*0.50673830 RouterA BFD/8/SCM:Sess[192.168.0.102/192.168.0.100,Eth1/1], Oper: Del
application(OSPF)
*0.50673831 RouterA BFD/8/SCM:No application in session, delete
session[192.168.0.102/192.168.0.100,Eth1/1]
*0.50673831 RouterA BFD/8/SCM:Sess[192.168.0.102/192.168.0.100,Eth1/1], Oper:
Delete
*0.50673832 RouterA BFD/8/SCM:Delete send-packet timer
*0.50673833 RouterA BFD/8/SCM:Delete session entry
*0.50673833 RouterA BFD/8/SCM:Delete session from IP hash table
*0.50673834 RouterA BFD/8/SCM:Delete session from bfd interface
*0.50673834 RouterA BFD/8/SCM:No session under bfd-int[Ethernet1/1] with default
configuration, delete bfd-if
*0.50673835 RouterA BFD/8/SCM:Bfd-if[Ethernet1/1], Oper: Delete
*0.50673840 RouterA BFD/8/SCM:No bfd session exists, stop receiving any bfd packets
# Display BFD information on Router A.
The BFD session between Router A and Router B is deleted, so no information is output.
<RouterA> display bfd session
# Display routes to 120.1.1.0/24 on Router A, and you can see that Router A communicates with
Router B through Router C.
<RouterA> display ip routing-table 120.1.1.0 verbose
Routing Table : Public
Summary Count : 2
Destination: 120.1.1.0/24
Protocol: OSPF
Preference: 10
IpPrecedence:
NextHop: 10.1.1.100
BkNextHop: 0.0.0.0
RelyNextHop: 0.0.0.0
Tunnel ID: 0x0
BKTunnel ID: 0x0
State: Active Adv
Process ID: 1
Cost: 4
QosLcId:
Interface: Ethernet1/2
BkInterface:
Neighbor : 0.0.0.0
Label: NULL
BKLabel: NULL
Age: 00h58m10s
110