GE t60 Instruction Manual page 140

5.4 FLEXLOGIC™
Table 5–7: T60 FLEXLOGIC™ OPERANDS (Sheet 4 of 4)
OPERAND TYPE OPERAND SYNTAX
INPUTS/OUTPUTS: REMOTE INPUT 1 On
Remote Inputs
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
Virtual Inputs
Virt Ip 32
INPUTS/OUTPUTS: Virt Op 1
Virtual Outputs
Virt Op 64
LED TEST LED TEST IN PROGRESS
REMOTE DEVICES REMOTE DEVICE 1 On
REMOTE DEVICE 16 On
REMOTE DEVICE 1 Off
REMOTE DEVICE 16 Off
RESETTING RESET OP
RESET OP (COMMS)
RESET OP (OPERAND)
RESET OP (PUSHBUTTON)
SELF- ANY MAJOR ERROR
DIAGNOSTICS ANY MINOR ERROR
ANY SELF-TEST
BATTERY FAIL
DIRECT DEVICE OFF
DIRECT RING BREAK
5
DSP ERROR
EEPROM DATA ERROR
EQUIPMENT MISMATCH
FLEXLOGIC ERR TOKEN
IRIG-B FAILURE
LATCHING OUT ERROR
LOW ON MEMORY
NO DSP INTERRUPTS
PRI ETHERNET FAIL
PROGRAM MEMORY
PROTOTYPE FIRMWARE
REMOTE DEVICE OFF
SEC ETHERNET FAIL
SNTP FAILURE
SYSTEM EXCEPTION
UNIT NOT CALIBRATED
UNIT NOT PROGRAMMED
WATCHDOG ERROR
UNAUTHORIZED UNAUTHORIZED ACCESS
ACCESS ALARM
USER- PUSHBUTTON x ON
PROGRAMMABLE PUSHBUTTON x OFF
PUSHBUTTONS
Some operands can be re-named by the user. These are the names of the breakers in the breaker control feature, the ID
(identification) of contact inputs, the ID of virtual inputs, and the ID of virtual outputs. If the user changes the default name/
ID of any of these operands, the assigned name will appear in the relay list of operands. The default names are shown in
the FlexLogic™ Operands table above.
The characteristics of the logic gates are tabulated below, and the operators available in FlexLogic™ are listed in the Flex-
Logic™ Operators table.
5-62
OPERAND DESCRIPTION
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
An LED test has been initiated and has not finished.
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Reset command is operated (set by all 3 operands below)
Communications source of the reset command
Operand (assigned in the
of the reset command
Reset key (pushbutton) source of the reset command
Any of the major self-test errors generated (major error)
Any of the minor self-test errors generated (minor error)
Any self-test errors generated (generic, any error)
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
Asserted when a password entry fails while accessing a password-protected
level of the relay.
Pushbutton Number x is in the 'On' position
Pushbutton Number x is in the 'Off' position
T60 Transformer Management Relay
↓
↓
↓
↓
↓
INPUTS/OUTPUTS
5 SETTINGS
menu) source
RESETTING
GE Multilin