Opti Cal Disc Recording Soft Ware Disclaimer; Safety And Compliance Informati On; Safety Precauti Ons - Rimage Professional 3400 User Manual

Rimage Professional 3400 and 5400N User Guide

Opti cal Disc Recording Soft ware Disclaimer

This Product, Soft ware, or Documentati on may be designed to assist you in reproducing material in which you own the
copyright or have obtained permission to copy from the copyright owner. Unless you own the copyright or have permission
to copy from the copyright owner, you may be violati ng copyright law and be subject to payment of damages and other
remedies. If you are uncertain about your rights, you should contact your legal advisor. If you are neither in possession of
the copyright nor have authorizati on from the owner of the copyright, unauthorized copying of copyrighted material on an
opti cal disc or any other media violates nati onal and internati onal legislati on and can result in severe penalti es.

Safety and Compliance Informati on

This manual and the indicati ons on the product allow proper and safe operati on. The indicati on marks below help protect
you and other persons from injury, and equipment from damage.

Safety Precauti ons

To ensure safety, read these precauti ons and familiarize yourself with their meaning before using the equipment.
 
Warnings!
•
The laser beam used by the CD/DVD Recorder is a Class 1
laser. Do not att empt to open the recorder. An authorized
technician should perform all service procedures.
•
Use of controls or adjustments or performance of
procedures other than those specifi ed herein may result
in hazardous radiant exposure.
•
Never use any opti cal instrument in conjuncti on with this
unit. To do so will greatly increase the hazard to your
eyes.
•
Use of controls or adjustments or performance of
procedures other than those specifi ed herein may result
in hazardous radiant exposure.
•
Do not disassemble or use tools on the printer. All service
procedures should be performed by a Rimage-authorized
technician, or sent in for Rimage-authorized repair.
•
The interior of the printer contains sharp edges.
•
Do not touch the heat roller.
•
Do not touch the circuit boards. The circuit boards can be
damaged by electrostati c.
•
Do not remove the back panel unless the autoloader has
been powered off .
•
Changes or modifi cati ons not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
•
This transmitt er must not be co-located or operated in
conjuncti on with any other antenna or transmitt er.
•
This equipment complies with FCC radiati on exposure
limits set forth for a controlled equipment and meets
the FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65. This equipment has very low
levels of RF energy that it deemed to comply without
maximum permissive exposure evaluati on (MPE). But
it is desirable that it should be installed and operated
keeping the radiator at least 20cm or more away from
person's body (excluding extremiti es: hands, wrists, feet
and ankles).
8

Cauti ons:
•
For conti nued protecti on against risk of fi re, replace the
fuse only with the same type and rati ng. An authorized
technician should perform all service procedures.
•
Use only the supplied AC power cord, or use a safety
agency approved power cord. For applicati ons outside
North America, refer to the nearest Rimage offi ce for
assistance in selecti ng a locally approved power cord.
•
This product is designed for an offi ce environment.
•
The Professional 3400 and 5400N contain a lithium
batt ery. There is a risk of explosion if the batt ery is
replaced by an incorrect batt ery. Dispose of the old
batt ery according to the manufacturer's instructi ons
included with the batt ery packaging.
•
All equipment with AC line voltage, or low DC voltages,
such as switches, power supplies, fuses, fans, and non-
stepper motors, must be replaced with Rimage-approved
components to maintain the safety approval issued by
UL.
•
Allow suffi cient free space for opening the printer tray.
Do not touch the printer tray while it is in moti on.
•
If the side cover is opened while power is supplied, the
printer will stop. Do not reach into the printer while
it is in operati on. Do not att empt to bypass the door
interlock.
2001431_A