Table 5 Controller Communications Commands - Fluke 7103 User Manual

7103 Micro-Bath User's Guide
Interface Commands

Table 5 Controller Communications Commands

Command Description Command Format
Display Temperature
Read current set-point s[etpoint]
Set current set-point to n s[etpoint]=n
Read temperature t[emperature]
Read temperature units u[nits]
Set temperature units: u[nits]=c/f
Set temperature units to Celsius u[nits]=c
Set temperature units to u[nits]=f
Fahrenheit
Read scan mode sc[an]
Set scan mode sc[an]=on/off
Read scan rate sr[ate]
Set scan rate sr[ate]=n
Read hold ho[ld]
Secondary Menu
Read proportional band setting pr[opband]
Set proportional band to n pr[opband]=n
Read heater power po[wer]
(duty cycle)
Configuration Menu
Operating Parameters Menu
Read stirrer motor speed mo[tor]
Set stirrer motor speed to n mo[tor]=n
Read high limit hl
Set high limit hl=n
Serial Interface Menu
Read serial sample setting sa[mple]
Set serial sampling setting to n sa[mple]=n
seconds
Set serial duplex mode: du[plex]=f[ull]/h[alf]
Set serial duplex mode to full du[plex]=f[ull]
Set serial duplex mode to half du[plex]=h[alf]
Set serial linefeed mode: lf[eed]=on/of[f]
Set serial linefeed mode to on lf[eed]=on
Set serial linefeed mode to off lf[eed]=of[f]
Calibration Menu
Read R0 calibration parameter r[0]
Set R0 calibration parameter to n r[0]=n
Read ALPHA calibration al[pha]
parameter
Set ALPHA calibration parameter al[pha]=n
to n
Read DELTA calibration de[lta]
parameter
Set DELTA calibration parameter de[lta]=n
Read BETA calibration parameter be[ta]
Set BETA calibration parameter be[ta]=n
Functions not on menu
Read firmware version number *ver[sion]
Read structure of all commands h[elp]
Read all operating parameters all
Legend: [] Optional Command data
{} Returns either information
n Numeric data supplied by user
9 Numeric data returned to user
x Character data returned to user
Note: When DUPLEX is set to FULL and a command is sent to READ, the command is returned followed by a carriage return and
linefeed. Then the value is returned as indicated in the RETURNED column.
46
Shop for Fluke products online at:
Command Example Returned
s set: 999.99 {C or F}
s=200.00
t t: 999.99 {C or F}
u u: x
u=c
u=f
sc scan: {ON or OFF}
sc=on
sr srat: 99.9 {C or F}/min
sr=1.1
ho hold: open/closed,
99.9 {C or F}
pr pb: 999.9
pr=8.83
po po: 999.9
mo mo: 99
mo=16
hl hl:999
hl=90
sa sa: 9
sa=0
du=f
du=h
lf=on
lf=of
r r0: 999.999
r=100.324
al al: 9.9999999
al=0.0038433
de de:9.99999
de=1.3742
be be:99.999
be=0.342
*ver ver.9999,9.99
h list of commands
all list of parameters
MyFlukeStore
www.
Returned Example Acceptable Values
set: 150.00 C
Instrument Range
t: 55.6 C
u: C
C or F
scan:ON
ON or OFF
srat:12.4C/min
.1 to 99.9
hold: open, 30.5 C
pb: 15.9
Depends on
Configuration
po: 1.0
mo: 15
0 to 40
hl:126
0–126
sa: 1
0 to 999
FULL or HALF
ON or OFF
r0: 100.578
90 to 110
al: 0.0038573
.002 to .005
de: 1.507
0–3.0
be:03427
–20 to 20
ver.7103,2.00
1.877.766.5412
.com