GE P741 Technical Manual page 272

P74x/EN PL/Na7
(PL) 7-38
DDB
Relay
No.
P743 484 IM Data CD Fail
P743 485 IM Channel Fail
P743 486 Backup Setting
P743 512 GOOSE OUT 1
P743 543 GOOSE OUT 32
P743 584 InterMiCOM in 1
P743 591 InterMiCOM in 8
P743 592 InterMiCOM out 1 INTEROUT
P743 599 InterMiCOM out 8 INTEROUT
P743 600 CBF I< Start A
P743 601 CBF I< Start B
P743 602 CBF I< Start C
P743 603 CBF I> Start A
P743 604 CBF I> Start B
PL
P743 605 CBF I> Start C
P743 606 CBF I> Start N
P743 608 Control Input 1
P743 639 Control Input 32
P743 640 LED 1 Red
P743 641 LED 1 Grn
P743 654 LED 8 Red
P743 655 LED 8 Grn
P743 656 FnKey LED 1
Red
P743 657 FnKey LED 1 Grn TRI_LED
P743 674 FnKey LED 10
Red
P743 675 FnKey LED 10
Grn
P743 676 Function Key 1
P743 685 Function Key 10
P743 700 Relay condit 01
P743 715 Relay condit 16
P743 764 LED 1 Red
Condit
P743 765 LED 1 Grn Condit TRI_LED_CON
P743 778 LED 8 Red
Condit
English Text Type
PSL Input Signal
PSL Input Signal
PSL Input Signal
GOOSEOUT
GOOSEOUT
INTERIN
INTERIN
PSL Output
Signal
PSL Output
Signal
PSL Output
Signal
PSL Output
Signal
PSL Output
Signal
PSL Output
Signal
PSL Output
Signal
CONTROL
CONTROL
TRI_LED
TRI_LED
TRI_LED
TRI_LED
TRI_LED
TRI_LED
TRI_LED
FUNCTION_KEY
FUNCTION_KEY
OUTPUT_CON
OUTPUT_CON
TRI_LED_CON
TRI_LED_CON
Source
InterMiCOM InterMiCOM Data Channel Detect Fail
InterMiCOM InterMiCOM Channel Failure Alarm
InterMiCOM Backup setting Alarm
This is an alarm that is ON if any setting fail
during the setting changing process. If this
happens, the relay will use the last known good
setting.
PSL GOOSE Output 1
Allows user to control a binary signal which can
be mapped via SCADA protocol output to other
devices
PSL GOOSE Output 32
Allows user to control a binary signal which can
be mapped via SCADA protocol output to other
devices
InterMiCOM InterMiCOM IM1 Signal Input - is driven by a
message from the remote line end
InterMiCOM InterMiCOM IM8 Signal Input - is driven by a
message from the remote line end
InterMiCOM InterMiCOM IM1 Signal Output - mapping what
will be sent to the remote line end
InterMiCOM InterMiCOM IM8 Signal Output - mapping what
will be sent to the remote line end
50BF Protection Phase A undercurrent CBF Dead Pole Start
50BF Protection Phase B undercurrent CBF Dead Pole Start
50BF Protection Phase C undercurrent CBF Dead Pole Start
50BF Protection Phase A overcurrent CBF Dead Pole Start
50BF Protection Phase B overcurrent CBF Dead Pole Start
50BF Protection Phase C overcurrent CBF Dead Pole Start
50BF Protection Neutral overcurrent CBF Dead Pole Start
Control Input Control Input 1 - for SCADA and menu
Command commands into PSL
Control Input Control Input 32 - for SCADA and menu
Command commands into PSL
PSL (LED) Programmable LED 1 Red is energized
PSL (LED) Programmable LED 1 Green is energized
PSL (LED) Programmable LED 8 Red is energized
PSL (LED) Programmable LED 8 Green is energized
PSL (LED) Programmable Function Key LED 1 Red is
energized
PSL (LED) Programmable Function Key LED 1 Green is
energized
PSL (LED) Programmable Function Key LED 10 Red is
energized
PSL (LED) Programmable Function Key LED 10 Green is
energized
PSL (Function Key) Function Key 1 is activated.
In 'Normal' mode it is high on key press and in
'Toggle' mode remains high/low on single key
press
PSL (Function Key) Function Key 10 is activated.
In 'Normal' mode it is high on key press and in
'Toggle' mode remains high/low on single key
press
Output Conditioner Input to Relay Output Conditioner
Output Conditioner Input to Relay Output Conditioner
Output Conditioner Assignment of input signal to drive output LED
1Red
Output Conditioner Assignment of signal to drive output LED
1Green.
To drive LED1 Yellow DDB 764 and DDB 765
must be driven at the same time
Output Conditioner Assignment of signal to drive output LED 8Red
Programmable Logic
MiCOM P741, P742, P743
Description