GE P741 Technical Manual page 260

P74x/EN PL/Na7
(PL) 7-26
DDB
Relay
No.
P742 261 Dead Zone Fault
P742 262 Dead Zone
Phase
P742 263 Dead Zone Earth
P742 264 Config OK
P742 265 Config Error
P742 266 Config Error
P742 267 Config. Valid
P742 268 Topology valid
P742 269 Topo/Set valid
P742 270 All Prot Blocked
P742 288 I> Any Trip
P742 289 CBAvailabToTrip
P742 290 BF Trip Request
P742 294 INP Block
87BB/P
P742 295 INP Block
87BB/N
P742 296 I> No Trip
P742 297 CBNotAvailToTrip PSL Input Signal
P742 298 BFTripNoRequest PSL Input Signal
P742 305 Ctrl CB Trip
P742 306 Ctrl CB Close
PL
P742 307 PU Overhaul
mode
P742 308 50BF Disabled
P742 311 50BF Disabled
P742 312 Overhaul Mode
P742 314 I>BB Enabled
P742 315 Trip Rel Latched
P742 316 I>2 Block BB ON
P742 317 IN>2 Block BB
ON
P742 318 Reset Trip Relay
P742 319 Topo/Set
Changed
P742 320 Q1 Closed
P742 321 Q1 Status Alarm
P742 330 Q6 Closed
P742 331 Q6 Status Alarm
P742 332 CB Closed
P742 333 CB Healthy
P742 336 Q1 Status Forced PSL Input Signal
P742 341 Q6 Status Forced PSL Input Signal
P742 342 CB Status Forced PSL Input Signal
P742 343 Forced Mode ON
P742 344 CB Aux. 52a
P742 345 CB Aux. 52b
English Text Type
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Output
Signal
PSL Output
Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Output
Signal
PSL Input Signal
PSL Output
Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
PSL Input Signal
Source
Local Protection Fault in the dead zone
Local Protection Fault in the dead zone on a phase
Local Protection Fault in the dead zone on the neutral
Relay Integrity Correct configuration
Relay Integrity Configuration error
Relay Integrity Configuration error
Scheme Integrity Valid Setting configuration
Scheme Integrity Valid Topology file
Scheme Integrity Wrong Topology address
Commissioning All the protections (CU & PU) disabled
Phase Overcurrent Overcurrent Trip
Scheme Integrity Complement of ddb 297
50BF Protection External or internal Breaker failure trip order
request (50BF) Logical OR of DDB 122, 172
and 173
PSL Logic input to block the 87BB trip when the fault
is detected by the fault element
PSL Logic input to block the 87BB trip when the fault
is detected by the earth fault element
Phase Overcurrent Complement of ddb 288
Scheme Integrity Logical OR of ddb 121 and 270
50BF Protection Complement of ddb 290
Manual Manual Trip Order of the Circuit Breaker
Functionality
Manual Manual closing order of the Circuit Breaker
Functionality
Commissioning PU in overhaul mode
Commissioning PU in 50BF blocked mode Alarm
Commissioning To switch the PU in 50BF blocked mode
Commissioning To switch the PU in overhaul mode
Local protection Overcurrent Local trip confirmation
Local protection Trip Relays Latched
87BB protection Fast external phase fault criterion to block the
connected zone enabled
87BB protection Fast external neutral fault criterion to block the
connected zone enabled
Commissioning To reset the Trip relays
Commissioning Change on topology or configuration
PSL Isolator 1 closed (not (Q1 Aux. (89b) AND Q1
Aux. (89a)))
Scheme Integrity Isolator 1 discrepancy (Q1 Aux. (89b) = Q1
Aux. (89a) for too long
PSL Isolator 6 closed (not (Q6 Aux. (89b) AND Q6
Aux. (89a)))
Scheme Integrity Isolator 6 discrepancy (Q6 Aux. (89b) = Q6
Aux. (89a) for too long
PSL Circuit Breaker closed (not (CB Aux. (52b) AND
CB Aux. (52a)))
PSL Complement of ddb 121
Commissioning Isolator 1 status position forced open (by
default) or closed
Commissioning Isolator 6 status position forced open (by
default) or closed
Commissioning CB status position forced open (by default) or
closed
Commissioning When the forced positions of the CB and the
Isolators are used (during commissioning test)
CB Monitoring ddb 123 or Logical OR of ddb 125 and 127 and
129
CB Monitoring ddb 124 or Logical AND of ddb 126 and 128
and 130
Programmable Logic
MiCOM P741, P742, P743
Description