Advertisement
Quick Links
XSVI-9004-NAV
Audi CAN Interface
AUDI
Applications below use
LD-AX-XSVI-AU1:
A3*
2006-2013
A4/RS 4/S4 with NAV
2005-2008
A4/RS 4/S4
2007-2008
A4/RS 4/S4*
2006
TT
2008-2013
FEATURES
• Provides accessory (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
• Prewired ASWC-1 harness (ASWC-1 sold separately)
• Retains balance and fade
• Micro "B" USB updatable
INTERFACE COMPONENTS
• XSVI-9004 interface • LD-AX-XSVI-AU1 harness • LD-AX-XSVI-AU2 harness
INSTALLATION INSTRUCTIONS FOR PART XSVI-9004-NAV
2002-2013
APPLICATIONS
Applications below use
LD-AX-XSVI-AU2:
A3**
2006-2007
A4/S4***
2002-2006
A6
2004
allroad
2004-2005
TT
2002-2006
Note:
* Only for models with either a
radio
Symphony Plus or NAV
**
With Concert radio (without NAV) ***
With Symphony radio
(without NAV)
TOOLS REQUIRED
• Cutting tool • Crimping tool • Tape • Connectors
(example: butt-connectors, bell caps, etc.)
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
Advertisement
Related Manuals for Axxess XSVI-9004-NAV
Summary of Contents for Axxess XSVI-9004-NAV
- Page 1 INSTALLATION INSTRUCTIONS FOR PART XSVI-9004-NAV XSVI-9004-NAV Audi CAN Interface 2002-2013 TOOLS REQUIRED APPLICATIONS • Cutting tool • Crimping tool • Tape • Connectors AUDI Note: Applications below use Applications below use (example: butt-connectors, bell caps, etc.) LD-AX-XSVI-AU1: LD-AX-XSVI-AU2: * Only for models with either a radio Symphony Plus or NAV A3* 2006-2013...
-
Page 2: Connections To Be Made
XSVI-9004-NAV Connections to be made From the LD-AX-XSVI-AU1 harness to the aftermarket radio • Connect the Blue wire to the amp turn on wire (this wire must be connected to hear sound from the factory amplifier). (a) From the 12-pin harness: • Connect the Red wire to the accessory wire. The following wire is for an aftermarket multimedia/navigation radio that provides this wire, if not required, tape it off and disregard it: • Connect the Orange wire to the illumination wire, if the aftermarket radio has • Connect the Blue/Pink wire to the speed sense wire (V.S.S.), if applicable. no illumination wire, tape off the Orange wire. • Connect the Blue/White wire to the amp turn on wire (this wire must be For non-BOSE systems: connected to hear sound from the factory amplifier). • Disregard the White RCA, it will not be used in this application. Note: There is a Blue wire on the 40-pin harness to connect as well. -
Page 3: Troubleshooting
• With all connections completed, reconnect the negative battery terminal. • Connect the Purple RCA to the right rear RCA output • Initialize the interface by turning the ignition on for 30 seconds, then turn the ignition back off, then back on again. Tape off and disregard the following wires, they will not be used in Note: If using the ASWC-1, connect it after you initialize the XSVI-9004-NAV, with this application: the key in the off position. • The Green, Green/Black, Purple, Purple/Black, White, White/Black, Gray, and Gray/Black wires. Note: It is highly recommended that the radio being used has 2 sets Troubleshooting of RCA outputs to retain balance and fade;... - Page 4 XSVI-9004-NAV Connections to be made From the LD-AX-XSVI-AU2 harness to the aftermarket radio • Connect the Gray wire to the right front positive speaker output. • Connect the Gray/Black wire to the right front negative speaker output. (a) From the 12-pin harness: • Connect the Red wire to the accessory wire. Tape off and disregard the following wires, they will not be used in this application: • Connect the Orange wire to the illumination wire, if the aftermarket radio has no illumination wire, tape off the Orange wire. • The Green, Green/Black, Purple, Purple/Black wires. The following wires are for aftermarket multimedia/navigation radios that provide For BOSE systems: these wires (if not required, tape them off and disregard them): Tape off and disregard the following wires, they will not be used in • Connect the Light Green wire to the parking brake wire (if applicable).
- Page 5 Note: It is highly recommended that the radio being used has 2 sets of RCA Note: If using the ASWC-1, connect it after you initialize the XSVI-9004-NAV, with outputs to retain balance and fade; 3 sets if a subwoofer amplifier will be the key in the off position.